JBL Speaker SAM1HF User Manual

®
SYNTHESIS ARRAYMODULE  
SAM1HF,  
SAM2LF  
MODULAR ARRAY  
LOUDSPEAKER  
OWNER S AND  
INSTALLER S  
MANUAL  
 
INTRODUCTION  
®
Thank you for purchasing this JBL Synthesis Array Module home theater speaker. This product represents the  
synthesis of everything that JBL has learned about the emotional power of audio and video in sixty years of preemi-  
nence in the field. It sets new benchmarks in the use of “high technology” and provides you with the experience of  
being in some of the world’s greatest movie houses and concert halls, right at home! JBL’s Synthesis Array speaker  
systems feature the following:  
®
THX ULTRA2 -LICENSED HOME AUDIO SYSTEM: When used with a THX controller and amplifiers, your  
speaker system will deliver a state-of-the-art THX home theater experience to your living room. You will hear in your  
home exactly what the director and sound engineer heard in the recording studio. The system will reproduce the  
audio flawlessly and without distortion.  
ULTRAHIGH-FREQUENCY COMPRESSION DRIVER: 1" (25mm) Pure-titanium compression driver with aluminum  
®
edge-wound voice coil and 2" (51mm) neodymium motor assembly, mounted in a SonoGlass constant-directivity  
horn for extended high-frequency response to exceed SACD and DVD-Audio specifications.  
HIGH-POWER COMPRESSION HORN: Horns are commonplace in movie theaters across the world, because  
of their high power handling and well-defined high-frequency output. The horns employed in SAM1HF have very  
low distortion and a well-controlled directivity, to put the dialogue at the center of the screen and the effects all  
around you.  
ACCURATE MID-BASS DRIVERS AND SUBWOOFERS: The 8" (200mm) mid-bass drivers incorporate many of  
JBL’s patented technologies – such as Symmetrical Field Geometry (SFG), Symmetrical Inductance Modulation (SIM)  
and Vented Gap Cooling (VGC) – as well as unique cone and dome materials, to provide tight, smooth midrange  
sound without harshness, stridency or listener fatigue. From two to as many as four 15" or 18" (380mm or 457mm)  
high-power subwoofers complete the experience with earth-shattering, deep bass.  
COMMON VOICING: Synthesis Array uses common voicing across the front three channels. Since identical drivers  
are used, each speaker has the same tonal qualities, thus as a sound is panned from one side to the other, there will  
be no change in timbre.  
MAGNETIC SHIELDING: All front speakers are magnetically shielded, allowing you to place them near video mon-  
itors without generating interference or distorting the picture.  
DUAL “INSIDE” NEODYMIUM MOTOR STRUCTURE: Two neodymium magnets are used. The “top” neodymium  
magnet is magnetized with opposite polarity to the main, lower neodymium magnet. This inverted dual-magnet configu-  
ration improves magnetic shielding and offers increased acoustic output.  
DEEP-ANODIZED CONE AND DOME MATERIAL: The special deep-anodized aluminum cone and dome material,  
together with the motor features, helps to reduce midband distortions to very low levels (approximately 50dB to 60dB  
below the fundamental signal driven at 100dB output).  
TWO-STAGE PHASE PLUG: The phase plug is a key element in this compression driver. The accuracy of the phase  
plug geometry is most important to achieve a wide and flat frequency response. The pressure distribution in the phase  
plug is manipulated by adjustments to the number and width of the slots and is optimized to achieve a coherent  
pressure front across the operating range at the exit of the phase plug.  
SYMMETRICAL INDUCTANCE MODULATION (SIM): The flux-stabilizing ring and copper gap ring are also  
optimized for size and position, to help minimize or eliminate “asymmetrical inductance modulation.” Minimizing this  
asymmetrical inductance modulation leads to even further distortion reduction and improved vocal clarity.  
3
 
INCLUDED  
SAM1HF  
(2) mounting brackets: metal brackets for mounting to the SAM2LF module  
(4) knobs: used to securely hold the mounting brackets to the cabinet  
SAM2LF  
(2) mounting brackets: metal brackets for mounting to the SAM1HF module  
(4) knobs: used to securely hold the mounting brackets to the cabinet  
SPEAKER PLACEMENT  
Positioning your loudspeakers properly is critical in order to achieve the  
sonic performance of a home theater. Please read the following section  
for guidance in correct and optimal placement.  
L
C
R
LEFT AND RIGHT SPEAKERS: If you have purchased a Synthesis Array  
Module digital home theater system, then one of the configurations of the  
SAM1HF/SAM2LF modules will serve as your front left and right main  
speakers. Please see the Configuration and Connection diagrams in the  
“SAM1HF and SAM2LF Configuration and Assembly” section to  
correctly configure your main speakers.  
VIEWING  
POSITION  
Since the left and right speakers have been designed for maximum local-  
ization of sound, they should be placed with the center of the speakers at  
about the same height on screen as the actors would be, to aid in the illu-  
sion that the actors’ voices are coming directly from their on-screen images.  
Ideally, the speakers will be placed about 45 degrees apart from each other,  
viewed from the listening position, so that the distance between the speakers  
is the same as each speaker’s distance from the listener (see Figure 1).  
FLOOR PLAN  
Figure 1. 5.1-Channel system  
CENTER CHANNEL SPEAKERS: Please see the Configuration and  
Connection diagrams in the “SAM1HF and SAM2LF Configuration and  
Assembly” section to correctly configure your center speaker. Regardless  
of the configuration you have chosen, it is important to place the horn  
array vertically during installation in order to take advantage of its sound-  
dispersion characteristics. If you mount it horizontally, it will not provide the  
correct dispersion pattern. If the speaker is being used with a perforated  
projection screen, it should be mounted behind the center of the screen  
(see Figure 2).  
Figure 2.  
If a nonperforated projection screen, plasma display or other fixed video  
device is being used in the installation, then the recommended location is  
directly below (and as close as possible to) the video display (see Figure 3),  
although the inverse of this method will work also.  
Figure 3.  
4
 
SPEAKER PLACEMENT  
NOTE: It is extremely important to place the tweeter/mid-bass arrays for each of the center, left and right speakers  
at the same height. The horn array containing the tweeter in the center channel speaker should be no more than two  
feet (0.6 meter) higher or lower than those in the left and right speakers. This preserves the “localization integrity” of  
“sound pans,” in which the sound appears to move from left to center to right. If the program material also appears to  
travel up and down, it can destroy the illusion of panning effects and so should be avoided.  
AMBIENT SURROUND SPEAKERS: Although it has been common for many years to use a number of surround  
speakers in commercial movie houses, until recently, the traditional home theater configuration called for 5.1  
channels, i.e., front left, center, front right, surround left and surround right, plus a low-frequency effects channel.  
The newer surround formats that are appearing in consumer audio equipment are calling for more complicated 6.1-  
and 7.1-channel systems. The advantages of using additional speakers are many. Additional channels enable a more  
versatile use of directionality for a more accurate surround presentation. Also, a higher overall sound-pressure level  
can be achieved with less energy expenditure from any individual speaker. Placement of the surround speakers  
remains critical.  
5.1-CHANNEL SYSTEMS  
The ambient surround speakers work optimally if they are placed as far back from  
the screen as the viewing chairs are. If there are two rows of chairs, these speakers  
should be placed between them.  
The ambient surround speakers should be placed higher than the seating area, at  
least two feet (0.6 meter) above (seated) ear level (see Figure 4).  
The preferred method to mount the ambient surrounds is to put them directly in the  
side walls. This lets each speaker radiate to the front and back of the room and to  
reflect off the side walls.  
There are a few instances in which the ambient surrounds would perform  
better if mounted in the ceiling rather than the walls. If one or both of the walls  
are “acoustically dead,due to the presence of windows, fabric, furniture or other  
absorption, it may be necessary to turn the ambient speakers sideways and,  
instead of mounting them in a vertical orientation, mount them in the ceiling in  
a horizontal orientation.  
Figure 4.  
5
 
SPEAKER PLACEMENT  
6.1-CHANNEL SYSTEMS  
L
C
R
A 6.1-channel system can be thought of as a 5.1-channel system with the  
addition of a rear center speaker placed midway between the two surround  
speakers, and further to the rear than the surrounds. It should be placed at the  
same height as the side surround speakers (see Figure 5).  
7.1-CHANNEL SYSTEMS  
In a 7.1-channel system, two speakers are added for rear fill, in addition to the  
surround speakers in a 5.1-channel system. The two additional speakers are  
placed on the rear wall or near the rear wall in the ceiling (see Figure 6).  
FLOOR PLAN  
Figure 5. 6.1-Channel system  
L
C
R
SIDE  
LEFT  
SIDE  
RIGHT  
REAR RIGHT  
REAR LEFT  
Figure 6. 7.1-Channel system  
6
 
SAM1HF AND SAM2LF CONFIGURATION AND ASSEMBLY  
The different configurations of speaker arrays are accomplished by combining one (1) SAM1HF module with at least  
one (1) and up to four (4) SAM2LF modules. The configuration of your system depends greatly on room size and at  
what SPL the system will be used. The different array configurations can be used to customize individual speakers  
for any application in any system. Typical uses would be as front left, front right and center channel speakers, but  
they can also be used as direct radiating surround speakers. A basic speaker array will consist of one (1) SAM1HF  
and one (1) SAM2LF as a three-way bi-amped speaker with an active crossover located in the Synthesis Digital EQ  
or as a three-way passive speaker when used with the SAM12x crossover.  
NOTE: The SAM1HF is the high-frequency horn module, and the SAM2LF is the low-frequency woofer  
module; you must use at least one of each for a complete speaker system.  
The modules are physically connected to each other by using the included connecting bars and hand-tightened knobs  
to mount the modules together. There are multiple mounting points, and several bars should be used to maintain a  
rigid connection. Be careful while constructing the module array, as it may become unsteady and tip over.  
Make sure the completed speakers are securely mounted and will not fall over, as they may be very heavy  
and could cause serious damage if not properly handled.  
Any module can be connected to any other module. We have identified four recommended and supported config-  
urations. For all configurations, you should observe the following mounting guidelines:  
FOR VERTICAL MOUNTING:  
1. When mounting the SAM1HF to the SAM2LF with the SAM1HF on top, be sure to keep the modules from  
separating while you tighten the bars. This can be accomplished simply by keeping downward pressure on the  
front of the module while tightening the screws from the rear.  
2. Use at least two mounting bars, running from the top to the bottom of the modules.  
3. Use at least four hand screws, two on each module, with four on each module preferred.  
FOR HORIZONTAL MOUNTING:  
1. When mounting the SAM1HF to the SAM2LF, it is important to keep the top of the modules aligned. This is  
accomplished by turning the modules upside down before you begin mounting them together. Once you have  
finished, be sure to turn them right side up.  
2. Use at least two mounting bars, running from the top to the bottom of the modules.  
3. Use at least four hand screws, two on each module, with four on each module preferred.  
4. The bars will not extend beyond two modules. If you are connecting three across (as in a dual-woofer module  
design), use two sets of bars, each connected to the center module.  
FOR A COMBINATION OF HORIZONTAL AND VERTICAL MOUNTING:  
1. Attach the vertical modules first.  
2. Attach the horizontal modules second.  
3. Overlap the mounting bars so that they form a stiff construction.  
TRIM PANEL (BAFFLE BLOCKS) INSTALLATION:  
1. Purchase the correct trim panels for your configuration.  
2. The trim panels will act as both the cosmetic and structural finish of the speaker.  
7
 
SAM1HF AND SAM2LF CONFIGURATION AND ASSEMBLY  
IMPORTANT NOTE: Do not place the SAM1HF on its side. It must be mounted with the UHF DRIVER on the  
top, as shown below. Failure to do this will have a negative impact on the performance of this speaker.  
Detailed Configurations and System Connection  
Configuration 1: One SAM1HF and one SAM2LF vertical  
Configuration 2: One SAM1HF and one SAM2LF horizontal  
NOTE: Shown without the trim panel (baffle blocks) installed on the SAM1HF.  
8
 
SAM1HF AND SAM2LF CONFIGURATION AND ASSEMBLY  
Configuration 3: One SAM1HF and two SAM2LF horizontal  
NOTE: Shown without the trim panel (baffle blocks) installed on the SAM1HF.  
Configuration 4: One SAM1HF and two SAM2LF vertical  
NOTE: Shown without the trim panel (baffle blocks) installed on the SAM1HF.  
9
 
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM  
To connect the Synthesis Array loudspeakers to the power amplifiers or receiver, use two-conductor insulated speaker  
wire. We recommend #14 AWG wire as a minimum size. Your JBL dealer can recommend suitable cables. Both the  
SAM1HF and SAM2LF utilize push-style friction binding posts that can accommodate up to #10 AWG stranded wire.  
PREPARING THE HOOKUP WIRE  
1. First determine the distance between your amplifier and the most distant speaker in each group (fronts, surrounds,  
back surrounds, subwoofers).  
2. Now make the hookup wires for all speakers in each group this length, even if one speaker is much closer to your  
amplifier than the other. This will help maintain proper signal balance.  
3. Strip off 3/8" (10mm) of insulation from both ends of each conductor.  
4. Twist each set of standard wires into a tightly bunched spiral.  
5. Speakers and electronics terminals have corresponding (+) and (–) terminals. Most manufacturers of speakers and  
electronics, including JBL, use red to denote the (+) terminal and black for the (–) terminal, although some elec-  
tronics manufacturers have adopted the new color-coding standard promulgated by the Consumer Electronics  
Association. In that case, the positive terminal will be colored to correspond to the channel position, while the  
negative terminal will be black.  
It is important to connect all speakers identically: (+) on the speaker to (+) on the amplifier and (–) on the speaker to  
(–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and poor imaging.  
With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the  
correct polarity remains equally important to preserve the proper ambience and directionality of the program material.  
Now find a visual difference between the two conductors of each molded pair of speaker wires. Differentiating  
marks can be a different color wire (copper or silver); a strand of yarn in one conductor; thin, raised ribs on one part  
of the outer insulation; or a printed marking on one part of the outer insulation. It doesn’t matter which of the two  
strands go to the (+) and (–) on the speakers and amplifiers, as long as all speakers are connected identically. Push  
down on the binding post, insert the wire into the hole, and release.  
CONNECTIONS TO THE SYNTHESIS ELECTRONICS  
The SAM1HF and SAM2LF speaker modules do not have a built-in crossover. They must be used with the active  
crossover as designed in the SDEC-4000 digital equalizer in a bi-amplified configuration or with the outboard passive  
crossover, SAM12x, with the SDEC-3000. Each SAM module will require a single amplifier channel in a bi-amplifed  
system. Connect the SAM modules according to the chart on the following page.  
NOTES:  
• The SAM1HF will connect to the HI output of the SDEC-4000 or SAM12x.  
• The SAM2LF will connect to the LOW output of the SDEC-4000 or SAM12x.  
• Please consult the SDEC-4000 and SDEC-3000 installation guide for detailed instructions.  
• DO NOT use a full-range output from an amplifier, as damage may occur unless you are using the SAM12x.  
10  
 
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM  
INPUT/OUTPUT ASSIGNMENTS WITH ACTIVE CROSSOVER (BI-AMPED)  
Surround Processor to SDEC-4000P Inputs  
SDEC-4000P Outputs to Amplifiers  
S4000IC  
S4000IC  
Number  
Channel  
SDEC-4000P  
Number  
21  
22  
23  
24  
Channel  
SDEC-4000P  
1
FRONT LEFT  
A1  
SUBWOOFER 1  
SUBWOOFER 2  
SUBWOOFER 3  
SUBWOOFER 4  
D1  
D2  
D3  
D4  
2
3
4
5
6
7
8
FRONT RIGHT  
CENTER  
LEFT SIDE  
RIGHT SIDE  
LEFT REAR  
RIGHT REAR  
SUBWOOFER  
N/C  
A2  
A3  
A4  
B1  
B2  
B3  
B4  
C1  
C2  
C3  
C4  
NOTE: You must also connect  
®
both the CobraNet audio con-  
nections and Ethernet control  
connections to complete the  
installation. See the SDEC-4000  
installation guide for detailed  
instructions.  
N/C  
N/C  
N/C  
SDEC-4000X Outputs to Amplifiers  
S4000IC  
Number  
9
10  
11  
12  
13  
14  
15  
16  
Channel  
LEFT FRONT-LOW  
LEFT FRONT-HI  
RIGHT FRONT-LOW  
RIGHT FRONT-HI  
CENTER FRONT-LOW  
CENTER FRONT-HI  
LEFT SIDE 1  
LEFT SIDE 2  
N/C  
SDEC-4000X  
A1  
A2  
A3  
A4  
B1  
B2  
B3  
B4  
C1  
C2  
C3  
C4  
D1  
D2  
D3  
D4  
N/C  
17  
18  
RIGHT SIDE 1  
RIGHT SIDE 2  
N/C  
N/C  
19  
20  
LEFT REAR  
RIGHT REAR  
11  
 
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM  
SDEC-4000 With Bi-Amplified Speakers (Active Crossover)  
SDP-40  
INPUTS  
COMPONENT VIDEO  
MAIN OUTPUTS  
RECORD OUTPUTS  
1
2
3
3
4
4
5
5
INPUT  
1
INPUT  
INPUT  
2
4
INPUT  
3
Y
PR  
PB  
Y
PR  
PR  
PB  
Y
PR  
PB  
NOTE: Although the SDP-40  
is shown here, connections  
for the SDP-5 are similar.  
2
1
2
1
(OSD)  
OUTPUT  
PR PB  
Y
PB  
Y
VIDEO  
VIDEO  
1
2
6
7
8
Fix  
FRONT  
CENTER  
SIDE  
Fix  
Var  
Var  
SUBWOOFER  
REAR  
ZONE  
2
AUX  
(L)  
(R)  
(LS)  
(RS)  
(C)  
L
L
L
L
L
L
(SUB)  
R
R
R
R
R
R
LFE  
MICROPHONE INPUTS  
AUDIO  
TRIGGER OUTPUTS  
MAIN AUDIO OUTPUTS  
AUDIO  
S/PDIF  
1
2
5
3
1
2
3
4
1
4
2
5
3
1
2
4
6
IR IN  
6
RS 232  
FRONT  
CENTER  
LFE  
L
SUBWOOFER  
R
ZONE  
2
L
R
L
R
L
AUX  
R
L
R
L
SIDE  
R
REAR  
To Ethernet hub  
(for system calibration)  
SDEC-4000P  
SDEC-4000X  
To Ethernet hub  
(for system calibration)  
NO USER SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED PERSONNEL  
JBL SYNTHESIS  
NORTHRIDGE, CA  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
TRIGGERS  
S5160 POWER AMPLIFIER  
IN  
Ch.  
1
Ch.  
2
Ch.  
3
Ch.  
4
Ch.  
5
Input  
Input  
Input  
Input  
Input  
SPKR-1  
SPKR-2  
OUT  
MANUAL  
ON  
AUTO  
ON  
ON  
15A  
120V  
~
50/60Hz  
1800W  
OFF  
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture  
ATTENTION:  
VOIR LE CAHIER D'  
INSTRUCTION  
+
+
+
+
+
-
-
-
-
-
serial number  
Ch.  
1
Output  
Ch.  
2
Output  
Ch.  
3
Output  
Ch.  
4
Output  
Ch.  
5
Output  
S5160  
NO USER SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED PERSONNEL  
JBL SYNTHESIS  
NORTHRIDGE, CA  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
TRIGGERS  
S5160 POWER AMPLIFIER  
IN  
Ch.  
1
Ch.  
2
Ch.  
3
Ch.  
4
Ch.  
5
Input  
Input  
Input  
Input  
Input  
SPKR-1  
SPKR-2  
OUT  
MANUAL  
ON  
AUTO  
ON  
ON  
15A  
120V  
~
50/60Hz  
1800W  
OFF  
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture  
ATTENTION:  
VOIR LE CAHIER D'  
INSTRUCTION  
+
+
+
+
+
-
-
-
-
-
serial number  
Ch.  
1
Output  
Ch.  
2
Output  
Ch.  
3
Output  
Ch.  
4
Output  
Ch.  
5
Output  
S5160  
VOIR LE CAHIER D'  
INSTRUCTION  
JBL SYNTHESIS  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
ATTENTION:  
IN  
ATTENTION:  
VOIR LE CAHIER D'  
INSTRUCTION  
JBL SYNTHESIS  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
TRIGGERS  
TRIGGERS  
IN  
S800 POWER AMPLIFIER  
S800 POWER AMPLIFIER  
NORTHRIDGE, CA  
NORTHRIDGE, CA  
BRIDGED  
BRIDGED  
Ch.  
1
Ch.  
Input  
2
Ch.  
1
Ch.  
Input  
2
WARNING; To reduce the risk of fire or  
electric shock, do not expose  
WARNING; To reduce the risk of fire or  
electric shock, do not expose  
BRIDGED  
Input  
BRIDGED  
Input  
MONO  
STEREO  
MONO  
STEREO  
this appliance to rain or moisture  
this appliance to rain or moisture  
OUT  
OUT  
No user serviceable parts inside. Refer  
No user serviceable parts inside. Refer  
servicing to qualified personnel.  
AUTO  
MANUAL  
ON  
servicing to qualified personnel.  
AUTO  
MANUAL  
ON  
ON  
ON  
CAUTION  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
AVIS:  
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR  
AVIS:  
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR  
ON  
10A  
ON  
10A  
120V  
50/60Hz  
1200W  
~
120V  
~
50/60Hz  
1200W  
OFF  
OFF  
WARNING:  
serial number  
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
,
HAZARDOUS ENERGY  
,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
BRIDGED  
WARNING:  
serial number  
+
+
BRIDGED  
-
+
+
-
+
-
-
+
-
-
Ch.  
1
Output  
Ch.  
2
Output  
Ch.  
1
Output  
Ch.  
2
Output  
S800  
S800  
12  
 
CONNECTING THE SPEAKER TO THE REST OF YOUR SYSTEM  
INPUT/OUTPUT ASSIGNMENTS WITH PASSIVE CROSSOVER  
The SDEC-3000 supports up to 7.1 input with up to 7.1 output. The input and output assignments are as described  
in the below chart. You must make the correct connections from the surround processor output to the amplifier input  
for the system to work correctly. Please refer to the connection diagram for more information.  
The correct Synthesis Interconnect kit includes all the necessary connections for using the SDEC in the Synthesis sys-  
tem. Please be sure to order the S3000IC for use with SDEC-3000 and S4000IC for use with SDEC-4000. Retrofit kits are  
also available. Please contact JBL Synthesis Technical Support for more information at (888) 691-4171 (USA only).  
CONNECTION NOTES  
• Please follow the wiring diagram and the Input/Output Assignments chart for correct connections.  
• You will need to use the Ethernet network port on the rear panel of the unit for the final calibration process.  
You can use a crossover network cable if you plan to connect directly to the SDEC-3000 from a computer.  
Alternatively, you can connect the SDEC-3000 through any standard Ethernet hub.  
• When using the SDP-40 processor, make sure the subwoofer (in speaker setup) is set to Mono output and connect  
to the Subwoofer Left output. Do not use the LFE output.  
NOTE: Place the SAM12x  
passive crossover as close  
to the speakers as possible.  
The SAM12x has a single  
speaker level input and multiple  
outputs for the SAM1HF and  
SAM2LF speaker modules.  
Surround Processor to SDEC-3000 Inputs  
S3000IC  
Number  
Channel  
LEFT FRONT  
RIGHT FRONT  
CENTER FRONT  
LEFT SIDE  
SDEC-3000  
1
2
3
4
5
6
7
8
A1  
A2  
A3  
A4  
B1  
B2  
B3  
B4  
RIGHT SIDE  
LEFT REAR  
RIGHT REAR  
SUBWOOFER  
(Mono Sub Left)  
SDEC-3000 Outputs to Amplifiers  
S3000IC  
Number  
9
10  
11  
12  
Channel  
LEFT FRONT  
RIGHT FRONT  
CENTER FRONT  
LEFT SIDE  
SDEC-3000  
C1  
C2  
C3  
C4  
D1  
D2  
D3  
D4  
13  
14  
RIGHT SIDE  
LEFT REAR  
15  
16  
RIGHT REAR  
SUBWOOFER  
13  
 
CONNECTION TO THE REST OF THE JBL SYNTHESIS SYSTEM  
SDEC-3000 With Passive Crossover (SAM12x)  
SDP-5  
SDP-5 Digital Surround Processor/Controller  
INPUTS  
MAIN  
ZONE  
2
JBL, Inc. Northridge, CA  
Assembled in USA  
S/PDIF INPUTS  
2
1
3
2
4
TUV  
NOTE: Although the  
SDP-5 is shown here,  
connections for the  
SDP-40 are similar.  
INPUT  
1
INPUT  
2
Y
Y
PR  
PR  
PB  
PB  
Y
Y
PR  
PR  
PB  
PB  
C
US  
1
3
1
1
2
2
3
4
4
5
5
VIDEO  
VIDEO  
AUDIO  
CAUTION  
S/N  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
ATTENTION  
RISQUE DE CHOC  
ELECTRIQUE  
4
NE PAS OUVRIR  
OUTPUT  
CENTER  
INPUT  
7
3
IR IN  
3
6
8
FRONT  
SIDE  
REAR  
TRIGGER  
OUTPUTS  
(L)  
(R)  
(L)  
(R)  
(C)  
(LS)  
(RS)  
(C)  
(LS)  
(RS)  
L
L
L
S/PDIF  
OUT  
1
2
RS-232  
(SUB)  
(SUB)  
R
R
R
SUBWOOFER  
OUTPUTS  
1
2
AC 100-240V ~ 50-60 HZ, 60W  
SDEC-3000  
To Ethernet hub  
(for system calibration)  
S7150  
NO USER SERVICEABLE PARTS INSIDE. REFER  
JBL SYNTHESIS  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
TRIGGERS  
IN  
S5160 POWER AMPLIFIER  
SERVICING TO QUALIFIED PERSONNEL  
NORTHRIDGE, CA  
Ch. 1  
Input  
Ch. 2  
Input  
Ch. 3  
Input  
Ch. 4  
Input  
Ch. 5  
Input  
Ch. 6  
Input  
Ch. 7  
Input  
SPKR-1  
SPKR-2  
OUT  
MANUAL  
ON  
AUTO  
ON  
ON  
15A  
120V  
~
50/60Hz  
1800W  
OFF  
WARNING:  
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture  
SAM12x  
LEFT  
ATTENTION:  
VOIR LE CAHIER D'  
INSTRUCTION  
FRONT  
+
+
+
+
+
+
+
-
-
-
-
-
-
-
serial number  
Ch. 1 Output  
Ch. 2 Output  
Ch. 3 Output  
Ch. 4 Output  
Ch. 5 Output  
Ch. 6 Output  
Ch. 7 Output  
SAM12x  
RIGHT  
S800  
VOIR LE CAHIER D'  
INSTRUCTION  
ATTENTION:  
JBL SYNTHESIS  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
TRIGGERS  
FRONT  
S800 POWER AMPLIFIER  
IN  
NORTHRIDGE, CA  
BRIDGED  
Ch. 1  
BRIDGED  
Input  
Ch. 2  
Input  
WARNING; To reduce the risk of fire or  
electric shock, do not expose  
MONO  
STEREO  
this appliance to rain or moisture  
SAM12x  
CENTER  
FRONT  
OUT  
No user serviceable parts inside. Refer  
servicing to qualified personnel.  
AUTO  
MANUAL  
ON  
ON  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
AVIS:  
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR  
ON  
10A  
120V  
~
50/60Hz  
1200W  
OFF  
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
WARNING:  
serial number  
BRIDGED  
+
+
-
+
-
-
Ch. 1 Output  
Ch. 2 Output  
14  
 
TROUBLESHOOTING  
SYMPTOM  
PROBABLE CAUSE  
SOLUTION  
No sound coming  
from speaker  
• Amplifier not turned on  
Turn on amplifier.  
• Amplifier gain is low  
Make sure that there is  
amplifier gain for that channel.  
• Correct source not  
selected or turned on  
Select proper source.  
• Defective patch cords to amplifier  
Check/replace patch cords.  
• Speaker wires not  
Check speaker wire  
connected to amplifier  
connection to amplifier.  
• Balance control set improperly  
Make sure Balance control is set  
at center, or 12 o’clock, position.  
• Speaker wires damaged  
or shorted  
Make sure none of the speaker wires  
are frayed, cut or punctured. Make sure  
no wires are touching other wires or  
terminals and creating a short circuit.  
®
®
• Speaker not configured  
correctly  
In Dolby Digital or DTS mode, make  
sure that the receiver/processor is  
configured so that the speaker in  
question is enabled.  
®
• Center speaker is configured  
incorrectly  
In Dolby Pro Logic mode, make sure the  
center speaker is not in phantom mode.  
• Problem not diagnosed  
To diagnose the likely source of the  
problem, it is often helpful to switch the  
nonfunctioning speaker with one that  
is functioning correctly. Turn off all  
electronics before exchanging the  
speakers. Turn everything back on, and  
determine whether the problem is in  
the same place, or has moved with the  
speaker. If the problem is in the same  
place, the source is most likely with your  
receiver or amplifier. If the problem has  
followed the speaker, then contact your  
authorized JBL Synthesis custom installer  
or dealer for further assistance. If that  
is not possible, visit our Web site at  
Bass is very weak  
• Subwoofers are wired out  
of phase  
Make sure that positive terminals on the  
subwoofers go to the positive terminals  
on the amplifiers (red) and do the same  
for the negatives.  
• Subwoofers have not  
been placed optimally  
Experiment with different locations.  
15  
 
SPECIFICATIONS  
SAM1HF  
SAM2LF  
N/A  
ULTRAHIGH-FREQUENCY DRIVER  
HIGH-FREQUENCY TRANSDUCER  
045TI 1" (25MM) PURE-TITANIUM COMPRESSION DRIVER  
WITH ALUMINUM EDGE-WOUND VOICE COIL AND  
2" (51MM) NEODYMIUM MOTOR ASSEMBLY, MOUNTED  
IN A SONOGLASS® CONSTANT-DIRECTIVITY HORN  
435AL-1 3" (75MM) AQUAPLAS-TREATED ALUMINUM-DOME N/A  
COMPRESSION DRIVER WITH ALUMINUM EDGE-WOUND  
VOICE COIL AND NEODYMIUM MOTOR ASSEMBLY,  
MOUNTED IN A VERTICAL SONOGLASS® CONSTANT-  
DIRECTIVITY HORN  
LOW-FREQUENCY TRANSDUCER  
N/A  
8" (200MM) DEEP-ANODIZED ALUMINUM  
CONE AND DOME MATERIAL WITH DUAL  
INSIDENEODYMIUM MAGNETS, SHIELDED  
MOTOR STRUCTURE AND 2" (51MM)  
VOICE COILS  
SENSITIVITY (2.83V/1M)  
98DB  
92DB  
FREQUENCY RESPONSE (–3DB)  
36HZ TO 40KHZ*  
36HZ TO 40KHZ*  
300 WATTS  
N/A  
MAX. RECOMMENDED AMPLIFIER POWER 300 WATTS  
CROSSOVER FREQUENCIES  
NOMINAL IMPEDANCE  
9KHZ  
6 OHMS  
6 OHMS  
DIMENSIONS (H X W X D)  
17-1/4" X 8" X 11-1/2" **  
(438MM X 200MM X 292MM)  
20" X 10" X 10-3/4" **  
(508MM X 254MM X 273MM)  
WEIGHT PER SPEAKER  
25 LB (11KG)  
29 LB (13KG)  
* Note 1: Frequency response is for the complete speaker module, SAM1HF/SAM2LF together.  
** Note 2: Dimensions do not include mounting hardware or feet.  
Add 3" (75mm) depth for mounting hardware, and 1" (25mm) height for feet.  
Features, specifications and appearance are subject to change without notice.  
JBL, JBL Synthesis, Synthesis and SonoGlass are trademarks of Harman International Industries, Incorporated, registered in the United States  
and/or other countries. Array, Symmetrical Field Geometry and Vented Gap Cooling are trademarks of Harman International Industries, Incorporated.  
CobraNet is a registered trademark of Peak Audio, a division of Cirrus Logic, Inc.  
THX is a registered trademark, and THX Ultra2 is a trademark, of THX Ltd. All rights reserved.  
SACD is a trademark of Sony Corporation.  
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.  
DTS is a registered trademark of DTS, Inc.  
Declaration of Conformity  
We, Harman Consumer Group, Inc.  
2, route de Tours  
72500 Château du Loir  
France  
declare in own responsibility that the products described  
in this owner’s manual are in compliance with technical  
standards:  
EN 61000-6-3:2001  
Harman Consumer Group, Inc.  
250 Crossways Park Drive, Woodbury, NY 11797  
EN 61000-6-1:2001  
8500 Balboa Boulevard, Northridge, CA 91329  
818.830.8757  
Luc Guillaume  
Harman Consumer Group, Inc.  
Château du Loir, France 4/07  
Part No. 361697-001 4/07  
 

Jabra Microphone GN2100 IP User Manual
JBL Stereo Receiver AVR 140 User Manual
JL Audio Car Stereo System A1800 User Manual
JVC DVD Player XV M556TN User Manual
Kawasaki Automobile Parts KX100D5 User Manual
Kenwood MiniDisc Player KRC 597 User Manual
King Canada Air Compressor 8449 User Manual
KitchenAid Dishwasher KUDC20CVBL0 User Manual
Konica Minolta Digital Camera Dynax 60 User Manual
Konica Minolta Fax Machine 4556 9598 01A User Manual