Kenwood Automobile Accessories KPA H2C User Manual

 
Installation in a vehicle  
Note: Do not put Here2Anywhere in the docking station until you have completed the installation.  
Installation in a vehicle (continued)  
1. Determine where you want to mount 2. The leaves on the base can be bent to con-  
5. Plug the cigarette lighter adapter  
into the back of the cradle, as  
shown. Don’t plug the adapter into  
the cigarette lighter until the instal-  
lation is completed.  
6A. Plug the cassette adapter  
6B. If your car stereo has an aux input,  
plug the supplied audio cable into  
the back of the cradle instead of the  
cassette adapter. Plug the audio  
cable’s white (L ch,) and red (R ch.)  
connectors into your car stereo.  
4. Using the provided screw,  
assemble the docking station  
cradle to the base.  
Here2Anywhere.  
form to curved mounting surfaces.  
into the back of the cradle,  
as shown.  
• Do not install Here2Anywhere  
where it may obstruct your view  
through the windshield or your view  
of your vehicle’s indicator displays.  
• Do not install Here2Anywhere  
where it will hinder your access to  
the vehicle’s controls.  
• Do not install Here2Anywhere  
where it may hinder the function of  
safety devices such as an airbag.  
Doing so may prevent the air-bag  
from functioning properly in the  
event of an accident.  
• Find a location that provides good  
visibility of and access to  
Here2Anywhere’s front panel.  
3. Peel the covering away from the adhesive on  
the bottom of the base and adhere it to the  
mounting surface. Use the provided screws  
to securely attach the base to the surface.  
• If using screws, be sure that you do not  
damage wiring or other systems on the  
other side of the mounting surface.  
• Kenwood strongly recommends  
that you mount Here2Anywhere in a  
location where the base can be  
attached with the provided screws.  
4
5
KPA-H2C Installation Guide  
KPA-H2C Installation Guide  
 
Installation in a vehicle: Mounting the antenna  
Installation in a vehicle: Routing the cable  
Note: If you’re using the Kenwood CX-SR10 SIRIUS antenna, you’ll need to remove the plastic  
8. Route the cable from the antenna to the vehicle’s interior by  
tucking it underneath the rubber molding around rear window,  
as shown below.  
9. Route the cable from the lowest point of the rear win-  
dow into the trunk. Take advantage of any existing  
cable channels or wiring conduits.  
• For SUVs, minvans & 5-door vehicles, bring the  
cable into the vehicle under the rubber molding for  
the tailgate, and continue under the interior trim  
1. Temporarily plug the antenna  
into the “1-Sat/Terr (Main)  
connector on the back of the  
cradle until it is firmly seated,  
as shown.  
housings from the antenna connectors—we recommend labeling the wires with their respective  
colors. (See pg. 9, figure 16 of the CX-SR10 Installation Manual for details). Once you’ve  
removed the housings, connect the wire that had the yellow connector to the connector on the  
cradle labeled “1-Sat/Terr (Main)”, and connect the other one to the connector labeled “2-Terr”.  
2. Find an antenna location on a metal surface at least 12” x 12”, and at least 6” from a window.  
• Best reception is achieved with the antenna mounted on the roof; mounting on the trunk lid  
will work for convertibles.  
10. From the trunk, route the cable around the passenger  
compartment and to the back of the cradle.  
• If the vehicle has a roof rack or skid ribs, it may be necessary to mount the antenna off-center.  
3.The antenna’s powerful magnet will secure it to the metal surface.  
• Before routing the antenna cable, confirm that the antenna is mounted in a good location:  
4. Temporarily plug the cigarette lighter adapter into the cigarette lighter.  
5. Slide Here2Anywhere all the way into the cradle so that the connector at the rear of the unit  
makes proper contact in the cradle. Press the POWER button to turn Here2Anywhere on.  
6. Aim the remote control at Here2Anywhere, press the DIRECT button, then enter the number  
“1-8-4”, and press the SELECT button. If your Here2Anywhere has been properly connected and  
the antenna is receiving the SIRIUS signal you will hear audio. If you do not hear audio, the dis-  
play will read “Acquiring Signal”. Re-orient the antenna until you hear audio. (See Antenna  
Signal, on page 25 to use the ANTENNA SIGNAL screen to aim the antenna.)  
• Keep the wire away from areas where it could  
become tangled in driver’s and passenger’s feet.  
11. Plug the antenna into the back of the cradle  
(see pg. 6, Step 1).  
12. Plug the cigarette lighter adapter into the cigarette  
lighter.  
• KENWOOD RECOMMENDS UNPLUGGING THE  
CIGARETTE LIGHTER ADAPTER AFTER YOU TURN  
THE VEHICLE’S IGNITION OFF. (In some vehicles,  
the cigarette lighter remains active after the  
ignition has been turned off, and leaving  
Here2Anywhere’s cigarette lighter adapter  
plugged-into the cigarette lighter could drain the  
vehicle’s battery.)  
• Make sure the vehicle is not in garage, or somewhere the satellite signal could be blocked  
7. Turn Here2Anywhere’s power off and remove it from the cradle; unplug the cigarette lighter  
adapter from the cigarette lighter; unplug the antenna from the cradle.  
6
7
KPA-H2C Installation Guide  
KPA-H2C Installation Guide  
 
 

Insignia Flat Panel Television NS LCD32FS User Manual
Intel Computer Hardware S5721 xxx User Manual
Jackson Plumbing Product Whirl Wizard User Manual
JVC Stereo System CA MXGA3V User Manual
Kalorik Coffeemaker USK CCG 2 User Manual
Kenmore Vacuum Cleaner 11625812 User Manual
KitchenAid Double Oven KEMI371Y User Manual
KitchenAid Oven YKERS205TS User Manual
Klark Teknik Stereo Equalizer DN500 User Manual
Konica Minolta Camcorder 211 163 User Manual