Kenwood Car Stereo System DPX313 User Manual

DUAL DIN SIZED CD RECEIVER  
DPX503U  
DPX303  
DPX313  
INSTRUCTION MANUAL  
Declaration of Conformity with regard to the EMC Directive  
2004/108/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan  
EU Representative's:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands  
© B64-4227-00/00 (EW/ E2W)  
 
Before use  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• When you purchase optional accessories, check with  
your Kenwood dealer to make sure that they work  
with your model and in your area.  
• Characters that conform to ISO 8859-5 or ISO 8859-  
1 can be displayed. Refer to “MENU” > “Russian” of  
<Function Control> (page 6).  
2WARNING  
To prevent injury or fire, take the following  
precautions:  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
Before using this unit for the first time  
This unit is initially set on the Demonstration mode.  
When using this unit for the first time, cancel the  
<Demonstration mode Setting> (page 18).  
• The RDS feature won’t work where the service is not  
supported by any broadcasting station.  
• In this document, the description indicator will light  
means a status is displayed. Refer to <About Display  
Type> (page 9) for the details of the status display.  
How to reset your unit  
• The illustrations of the display, the function icon and  
the panel appearing in this manual are examples  
used to explain more clearly how the controls are  
used. Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
• If this unit or the connected unit (disc auto changer,  
etc.) fails to operate properly, press the Reset button.  
The unit returns to factory settings when the Reset  
button is pressed.  
Handling CDs  
• Do not touch the recording surface of the CD.  
• Do not stick tape etc. on the CD, or use a CD with  
tape stuck on it.  
• Do not use disc type accessories.  
Reset button  
• Clean from the center of the disc and move  
outward.  
• When removing CDs from this unit, pull them out  
horizontally.  
• If the CD center hole or outside rim has burrs,  
use the CD only after removing the burrs with a  
ballpoint pen etc.  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off with  
a cloth moistened with neutral cleaner, then wipe it  
again with a clean soft dry cloth.  
¤
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth or  
using a volatile liquid such as thinner or alcohol may scratch  
the surface or erases characters.  
CDs that cannot be used  
• CDs that are not round cannot be used.  
Lens Fogging  
When you turn on the car heater in cold weather,  
dew or condensation may form on the lens in the  
CD player of the unit. Called lens fogging, this  
condensation on the lens may not allow CDs to play.  
In such a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does not  
operate normally after a while, consult your Kenwood  
dealer.  
• CDs with coloring on the recording surface or CDs  
that are dirty cannot be used.  
• This unit can only play the CDs with  
.
This unit may not correctly play discs which do not  
have the mark.  
• You cannot play a CD-R or CD-RW that has not been  
finalized. (For the finalization process refer to your  
CD-R/CD-RW writing software, and your CD-R/CD-  
RW recorder instruction manual.)  
English  
|
3
 
Basic Operation  
[
]
Disc slot  
[SRC]  
[TI]  
[FNC]  
Control knob  
[1]—[6] USB Terminal Auxiliary input  
[AUD] [ATT]  
(DPX503U only)  
The audio system comes back on when [SRC] is  
pressed during a call.  
General functions  
Power/Source Select button: [SRC]  
Turns on the power.  
When the power is ON, select a source.  
SRC Select mode 1: Press the [SRC] button and then  
turn the Control knob or push it toward left or right.  
To determine the selected source, press the Control  
knob.  
SRC Select mode 2: Pressing this button each time  
switches between sources.  
Tuner (“TUNER”), USB or iPod (“USB” or “iPod”)  
(DPX503U only), CD (“Compact Disc”), Auxiliary input  
(“AUX”), and Standby (“STANDBY”)  
To use the TEL Mute feature, you need to hook up the MUTE  
wire to your telephone using a commercial telephone  
accessory. Refer to <Connecting Wires to Terminals> (page  
31).  
Auxiliary input: Auxiliary input  
Connect a portable audio device with mini-plug  
cable (ø3.5 mm).  
Use the mini-plug cable which is stereo type and does not  
have any resistance.  
The auxiliary input requires the setting made in “MENU” >  
Press at least 1 second to turn off the power.  
“Built in AUX” of <Function Control> (page 6).  
Subwoofer output: Control knob  
The SRC Select mode can be set in “MENU” > “SRC Select” of  
Switches between ON (“SUBWOOFER ON”) and OFF  
(“SUBWOOFER OFF”) each time pushing toward down  
for at least 2 seconds.  
<Function Control> (page 6).  
When an optional accessory is connected, the source name  
for each device appears.  
This unit automatically turns full power OFF after 20  
minutes lapses in Standby mode in order to save the  
vehicle's battery. The time until full power OFF can be set in  
“Power OFF” of <Function Control> (page 6).  
This function requires the setting made in “MENU” >  
“SWPRE” of <Function Control> (page 6).  
Function Control: [FNC]  
When connection of the iPod is recognized, the source  
display changes from “USB” to “iPod. (DPX503U only)  
Pressing this button allows you to set various  
functions using the Control knob. Refer to <Function  
Control> (page 6).  
Volume control: [AUD]  
Turn the knob to adjust the volume.  
Category  
MENU  
SOUND*  
DISP  
Function of setup item  
Attenuator: [ATT]  
Allows you to set up the environment.  
Allows you to set up the sound environment.  
Allows you to set up the display.  
Turning the volume down quickly.  
When the volume is reduced, the “ATT” indicator  
flashes.  
COLOR*  
Allows you to set up the illumination color.  
Muting volume upon reception of phone call  
When there is a call, “CALLis displayed and the audio  
system is paused.  
When the call ends, “CALLdisappears and the audio  
system comes back on.  
*Function of DPX503U  
Text/Title scroll: Control knob  
Scrolls the CD, audio file, and Radio text display when  
pushing toward up for at least 2 seconds.  
|
4
DPX503U/DPX303/DPX313  
 
Pause and play: Control knob  
Switches between pause and play each time the  
center is pressed.  
Tuner functions  
Band select: Control knob  
Switches between FM1, FM2, and FM3 each time  
USB device removing (DPX503U only): [0]  
Press this button for 2 seconds or longer to select the  
remove mode, and the remove the USB device.  
During the remove mode, the “USB REMOVE”  
indicator is ON.  
pushing toward up.  
Switches to AM when pushing toward down.  
Tuning: Control knob  
Changes the frequency when pushing toward left or  
right.  
Music search: Control knob  
Changes the music when pushing toward left or right.  
Fast reverses or forwards the music while keeping  
pushing toward left or right. (No sound is output  
while playing audio file.)  
During reception of stereo stations the “ST” indicator is ON.  
Auto memory entry:[TI]  
Memorizes six stations with good reception  
automatically when pressed for at least 2 seconds.  
Folder search: Control knob  
Changes the folder containing the audio file when  
Preset memory: [1] – [6]  
Memorize the station selected when pressing for at  
pushing toward up or down.  
least 2 seconds.  
Track/ File/ Folder repeat play: [4]  
Switches between Track Repeat (“Repeat ON”) and  
OFF when pressed while playing a CD.  
Preset tuning: [1] – [6]  
Recalls the memorized station.  
Switches between File Repeat (“File Repeat ON”),  
Folder Repeat (“Folder Repeat ON”), and OFF when  
pressed while playing an audio file.  
Traffic Information: [TI]  
Turns ON or OFF the Traffic Information function. If  
traffic bulletin starts when the function is ON, “Traffic  
INFO” is displayed and traffic information is received.  
The folder repeat operation cannot be performed  
while iPod is playing.  
If the volume is adjusted during reception of traffic  
information, the adjusted volume is memorized  
automatically. The memorized volume will be applied next  
time the Traffic Information function is turned ON.  
Scan play: [2]  
Successively plays the intro of the music in the disc  
or folder.  
Switches between ON (“Scan ON”/ “File Scan ON”) and  
OFF each time this button is pressed.  
Disc & Audio file play functions  
Disc play: Disc slot  
The Scan play operation cannot be performed while  
iPod/ “Media Editer” media is playing.  
Starts playing when a disc is inserted.  
When a CD is inserted, the “IN” indicator is ON.  
Random play: [3]  
Randomly plays the music in the disc or folder.  
Switches between ON (“Disc Random ON”/ “Folder  
RDM ON”) and OFF each time this button is pressed.  
3 inch (8 cm) CD cannot be used. Attempt to insert using  
an adapter can cause malfunction.  
Disc ejection: [0]  
You can eject the disc for 10 minutes after switching off the  
engine.  
USB device/iPod play (Function of DPX503U):  
USB Terminal  
Connecting a USB device starts playback.  
For the playable audio file, media, and devices, refer to  
<About Audio file> (page 26).  
English  
|
5
 
Function Control  
Functions in the table below can be set up by using Function Control.  
Category Item  
Setting  
Entry Setting overview  
1 sec.  
Condition Page  
Sets/Resets security code  
MENU  
“Security Set”/  
“Security Clear”  
“SRC Select”  
17  
Sets the source selection method.  
“1”*/“2”  
27  
13  
“iPod Mode”*1 “OFF”/ON”*  
When set to “ON, allows you to select music in the manner  
similar to that of the iPod.  
When the iPod source is used, sets whether the illumination  
color is changed by the iPod.  
“AT COL CHG”*1 “OFF”/iPod”*  
28  
Setting the operation check sound (beep sound) ON/OFF.  
“Beep”  
“OFF”/ON”*  
Sets the clock.  
Sets the date.  
“Clock Adjust”  
“Date Adjust”  
“Date Mode”  
“SYNC”  
1 sec.  
1 sec.  
1 sec.  
18  
18  
Sets the date display mode.  
7 types  
“OFF”/ON”*  
Synchronizing the RDS station time data and this unit’s  
clock.  
A red indicator will blink on the unit after the ACC is set to  
OFF, warning potential thieves.  
“DSI”  
“OFF”/ON”*  
Turns off the display when no operation is performed.  
“Display”  
“Dimmer”  
“OFF”/ON”*  
“OFF”/ON”*  
27  
27  
Dims the display part in conjunction with the light switch  
of the vehicle.  
Sets whether the illumination is dimmed in conjunction  
with the light switch of the vehicle or it is dimmed  
constantly.  
“ILM Dimmer” “AUTO”*/MNAL/  
“OFF”  
Sets whether the illumination color is changed in  
conjunction with the key operation. (To connect the  
Bluetooth unit)  
“ILM Effect”  
“OFF”/ON”*  
Sets whether the key illumination color is changed in  
conjunction with the sound volume.  
Sets the button illumination color.  
“ILM MSC SYNC” “OFF”*/ON”  
“ILM Color”*2  
“Blue”*/ ”Red”/  
”Green”  
Sets the preout output.  
“SWPRE”  
“AMP”  
“Rear”*/“Sub-W”  
27  
27  
27  
Turns on/off the built-in amplifier.  
“OFF”/ON”*  
Specifies the destination of AUX input sound when the Dual  
Zone function is turned on.  
“Zone2”  
“Rear”*/“Front”  
Turns ON/OFF the Supreme function.  
“Supreme”  
“OFF”/ON”*  
27  
Controls the connected LX amplifier.  
Turns ON/OFF the News Bulletin Automatic Reception  
function and sets the news bulletin interrupt disabled time.  
“AMS Control”  
“News”  
1 sec.  
18  
28  
“OFF”*/“00min”  
–“90min”  
Only stations whose reception is good are searched in auto  
seek tuning.  
Selects the tuning mode of the radio.  
“Local Seek”  
“Seek Mode”  
“AF”  
“OFF”*/ON”  
“Auto1”*/Auto2”/  
“Manual”  
“OFF”/ON”*  
28  
28  
When station reception is poor, automatically switches to  
the station that is broadcasting the same program over the  
same RDS network.  
Sets whether to switch to the station only in the specific  
region using the “AF” control.  
“Regional”  
“OFF”/ON”*  
When traffic information station reception is poor,  
automatically searches for a station that can be received  
better.  
“Auto TP Seek” “OFF”/ON”*  
You can reduce the noise when stereo broadcasts are  
received as monaural.  
“MONO”  
“OFF”*/ON”  
Sets the disc name (DNPS)/ AUX name.  
“Name Set”  
1 sec.  
11/12  
|
6
DPX503U/DPX303/DPX313  
 
Category Item  
“Russian”*3  
“Scroll”  
Setting  
“OFF”/ON”*  
Entry Setting overview  
Condition Page  
Selects Russian as the display language.  
28  
When set to “Auto, scrolls the screen once with the change  
of the displayed text.  
“Auto”/Manual”*  
Sets whether to display AUX during source selection.  
“Built in AUX” “OFF”/ON”*  
Turns off the power when the preset time has lapsed in the  
Standby mode.  
Sets the CD read mode.  
“Power OFF”  
“-----”/“20min”*/  
“40min”/“60min”  
“1”*/“2”  
28  
“CD Read”  
“Audio Preset”*2  
28  
24  
Presets the setting value of the audio control. The preset  
value is retained after resetting.  
1 sec.  
Switches the panel display between positive or negative.  
“DISP REVERSE” “POSI 1”/“POSI 2”/  
“NEGA 1”*/“NEGA 2”  
Adjusting the display contrast.  
“CONTRAST”  
“1”–“10”  
Sets the opening message displayed when the power is  
turned on.  
Specifies whether to enable demonstration.  
Selects the car type to compensate the distance difference  
between each speaker.  
Makes fine adjustment of the compensation value specified  
“OPENING MSGE  
Edit”  
1 sec.  
2 sec.  
12  
“DEMO Mode” “OFF”/ON”*  
18  
19  
/28  
SOUND*1 “S-SET” “CABIN” “Compact1”etc.  
“DTA”  
19/29  
at Cabin.  
Makes fine adjustment of the X’Over value specified at  
Speaker.  
“XOVER”  
20  
Sets the sound quality.  
“S-CTRL“EQ”  
“POSIT”  
20  
20  
/21  
Compensates the sound environment in accordance with  
the listening position.  
Compensates high and low pitch sound at lower volume.  
“LOUD” “OFF”*/ON”  
“PRESET”  
Presets the setting value of the audio control. The preset  
value is retained after resetting.  
Sets the display pattern.  
Sets the Type D spectrum analyzer display.  
Sets the Type A/B side icon display.  
21  
9
DISP  
“TYPE”  
“GRAPH”  
“SIDE”  
A/ B/ C/ D  
Î
Spectrum Analyzer 1 – 2  
Text icon/ Source  
icon/ OFF  
Åı  
Sets the text display.  
“TEXT”  
“OUT”  
ÅıÇ  
9
Sets the vehicle-side display.  
Sets the Panel illumination color.  
Presets a station.  
Color*1  
P.MEM  
SCAN  
10  
15  
When set to “ON, plays the intro of the music in the folder  
successively.  
“ON”/ —  
When set to “ON, plays the music in the folder randomly.  
RDM  
“ON”/ —  
“ON”/ —  
“ON”/ —  
“ON”/ —  
When set to “ON, plays the music repeatedly.  
FiREP  
FoREP  
SCAN  
When set to “ON, plays the music in the folder repeatedly.  
When set to “ON, plays the intro of the music on the disc  
successively.  
When set to “ON, plays the music on the disc randomly.  
RDM  
M.RDM  
“ON”/ —  
“ON”/ —  
When set to “ON, plays the music in the disc changer  
randomly.  
When set to “ON, plays the music repeatedly.  
T.REP  
D.REP  
“ON”/ —  
“ON”/ —  
When set to “ON, plays the music on the disc repeatedly.  
*Factory setting  
*1 Function of DPX503U.  
*2 Function of DPX303/DPX313.  
*3 Function of Russian sales model.  
Next page 3  
English  
|
7
 
Function Control  
Displayed item is depending on currently selected  
source or mode. The mark in Condition column shows  
the condition to which the item is displayed.  
: Can be set in other than standby state.  
: Can be set in standby state.  
1 Enter Function Control mode  
Press the [FNC] button.  
Function icon is displayed.  
2 Select your desired setup item  
: Can be set while Audio file source of CD/USB/iPod.  
: Can be set while Audio file source of CD/USB  
(excluding iPod).  
: Can be set while CD/ Disc changer source.  
: Can be set while Disc changer source.  
: Can be set during Tuner source.  
Operation type  
Operation  
Movement between items Turn the Control knob.  
Selection of item  
Press the Control knob.  
Return to previous item  
Press the [FNC] button or“  
”icon.  
Repeat selection and determination until your  
desired setup item is selected.  
: Can be set during FM reception.  
: Can be set while accessing AUX source.  
: Can be set only during playback of the iPod source.  
(USB source used when the iPod is connected)  
: Can be set for sources other than the standby source  
by setting “2 ZONE” of <Audio Setup> (page 23) to  
“ON.  
: Sets “ILM MSC SYNC” and “AT COL CHG” in the menu  
to “OFF.  
: Refer to the reference page.  
Example:  
MENU  
DISP COLOR  
DISP  
MENU  
COLOR  
TYPE  
SIDE TEXT  
In this manual, the above selection is  
indicated as  
Select “DISP” > “TYPE.  
ÅÎ : Can be set when the specified type is selected for  
Display Type.  
— : Can be set during all sources.  
3 Make a setting  
Turn the Control knob to select a setting value,  
and then press the Control knob.  
• The value of items with  
mark can be set by  
Refer to the respective page for information on how to  
set the items with reference page number.  
Only the items available to the current source are  
displayed.  
“ILM MSC SYNC” is displayed when “MENU” > “AT COL  
CHG” in <Function Control> is set to “OFF.  
Location played with “File Scan”  
pushing the Control knob towards right or left.  
• Some items require you to keep pressing the  
Control knob for 1 or 2 seconds so that you can  
make a setting. For these items, the time during  
which you need to keep pressing the Control  
knob is displayed in the Entry column in seconds.  
• For the functions accompanied by the  
- Audio file: First 10 seconds  
description of the setting procedure and so forth,  
the reference page numbers are displayed.  
- Music Editor media: First 10 seconds or the part picked  
by Intro Skip.  
During Intro Skip, turn the control knob left or right to  
change the song.  
The scan method depends on the Music Editor setting.  
See the Music Editor help for details.  
4 Exit Function Control mode  
Press the [FNC] button for at least 1 second.  
|
8
DPX503U/DPX303/DPX313  
 
Display Settings  
In Audio file source  
Information  
Music title & Artist name  
Album name & Artist name  
Folder name  
About Display Type  
Shown below are examples of display types.  
Display  
“Title/Artist”/”TITLE”  
“Album/Artist”/”ALBUM”  
“Folder Name”/”FOLDER”  
“File Name”/”FILE”  
“P-Time”/”P-TIME”  
“Speana/Clock”/”SPEANA”  
“Date”/”DATE”  
Display  
Display Type  
“TYPE [A]”  
3
1
1
File name  
Play time & Music number  
Spectrum Analyzer & Clock  
Date  
“TYPE [B]”  
“TYPE [C]”  
“TYPE [D]”  
2
3
Blank  
“Blank”/”BLANK”  
In Standby  
Information  
Standby  
Clock  
Date  
1
6
Display  
4
5
“Source Name”/”SRC NAME”  
“Clock”/”CLOCK”  
“Date”/”DATE”  
Blank  
“Blank”/”BLANK”  
1 Text display part  
2 Status display  
3 Icon display part  
4 Display (varied depending on the source)  
5 Clock display  
6 Spectrum Analyzer display  
In Auxiliary input source  
Information  
Auxiliary input name  
Spectrum Analyzer & Clock  
Date  
Display  
“Source Name”/”SRC NAME”  
“Speana/Clock”/”SPEANA”  
“Date”/”DATE”  
Blank  
“Blank”/”BLANK”  
1 Enter Text Display Selection mode (In Display  
Type A/ B/ C)  
Select “DISP” > “TEXT.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
Text Display Selection  
Changing the text display.  
In Tuner source  
Information  
2 Select the text display part  
Display  
Push the Control knob towards up or down.  
The selected text display part blinks.  
Program Service name (FM)  
Title & Artist name* (FM)  
Station name* (FM)  
Radio text plus* (FM)  
Radio text (FM)  
Frequency (MW, LW)  
Spectrum Analyzer & Clock  
Date  
“Frequency/PS”/“FREQ/PS”  
“Title/Artist”/”TITLE/ART”  
“Station Name”/”ST NAME”  
“Radio Text Plus”/”R-TEXT+”  
“Radio Text”/”R-TEXT”  
“Frequency”/”FREQ”  
“Speana/Clock”/”SPEANA”  
“Date”/”DATE”  
3 Select the text  
Turn the Control knob or push it towards left  
or right.  
4 Exit Text Display Selection mode  
Press the [FNC] button.  
Blank  
“Blank”/”BLANK”  
If the selected display item does not have any  
information, alternative information is displayed.  
Some items cannot be selected depending on the  
display type and row.  
When selecting “Folder Name” while playing with  
iPod, names will be displayed depending on currently  
selected browsing items.  
When Display Type C is selected, “Speana” is displayed  
instead of “Speana/Clock.”  
“Frequency” can be selected only on the first line while  
setting the text.  
* Information of Radio text plus is displayed.  
In CD & External disc source  
Information  
Disc title  
Track title  
Play time & Track number  
Disc name  
Display  
“Disc Title”/”D-TITLE”  
“Track Title”/”T-TITLE”  
“P-Time”/”P-TIME”  
“DNPS”  
Spectrum Analyzer & Clock  
Date  
“Speana/Clock”/”SPEANA”  
“Date”/”DATE”  
Blank  
“Blank”/”BLANK”  
When LX-AMP is connected, the item setup by the  
Display mode of LX-AMP is displayed.  
English  
|
9
 
Display Settings  
Function of DPX503U  
Function of DPX503U  
Illumination Color Selection  
Illumination Color Preset Memory  
Selecting the Illumination Color of the panel.  
Saving the combination of the Illumination Colors  
selected for each place. The memory cannot be  
erased by the Reset button.  
1 Enter Illumination Color Selection mode  
Select “Color” .  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
1 Set the Illumination Color for each place  
Refer to <Illumination Color Selection> (page 10).  
2 Select the place where you want to set the  
Illumination Color  
2 Enter Illumination Color Preset Memory mode  
Select “COLOR” > “PRESET” > “MEMO.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
Place  
Display  
All  
“All Color”  
Display  
Button  
Volume knob  
Control konb  
“Display Color”  
“Key Color”  
“Left Knob Color”  
“Right Knob Color”  
3 Put the Illumination Color Preset in the  
memory  
Press the Control knob.  
“Memory?” is displayed.  
Save and recall the Illumination Colors you selected “Color Preset”  
for each place  
4 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Memory Completed” is displayed.  
Turn the Control knob and push the center  
when the desired item is displayed.  
5 Exit Illumination Color Preset mode  
3 Select the Illumination Color  
Turn the Control knob and push the center  
when the desired item is displayed.  
Select the color from “Variable Scan”/ “Color1”  
— “Color 10”/ “User.  
Press the [FNC] button.  
Register 1 pair of Illumination Color Preset Memory.  
If you press the Reset button, the value in the memory  
will be default setting value of “Illumination Color  
Selection.”  
Creating “User” color  
You can create your original color during the  
selection from “Color1” — “Color10.”  
The color you created can be called when you  
select “User.  
1. Press the Control knob for at least 1 second.  
Enter the detail color adjustment mode.  
2. Set the color.  
Operation type  
Operation  
To select the color to adjust.  
(red, green, or blue)  
Push the Control knob towards  
right or left.  
To adjust color. (Range: 0 – 9) Turn the Control knob or push it  
towards up or down.  
3. Press the Control knob.  
Exit the detail color adjustment mode.  
4 Exit Key Color Selection mode  
Press the [FNC] button.  
When you select “PRESET, you can save the combination  
of the Illumination Colors selected for each place. For  
how to save Illumination Colors, refer to <Illumination  
Color Preset Memory> (page 10).  
|
10 DPX503U/DPX303/DPX313  
 
Function of DPX503U  
Disc Naming (DNPS)  
Attaching a title to a CD.  
Illumination Color Preset Recall  
Recalling the selection you saved in Illumination  
Color Preset mode.  
1 Play the disc you want to attach a name to  
2 Select Name set mode item during Menu  
1 Enter Audio Preset Recall mode  
Select “COLOR” > “PRESET” > “RECALL”.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
mode  
Select the “Name Set” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
2 Recall the Illumination Color Preset  
Press the Control knob.  
“Recall?” is displayed.  
3 Enter Name set mode  
Press the Control knob for at least 1 second.  
4 Enter the name  
Operation type  
Move the cursor to the enter  
character position  
3 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Recall Completed” is displayed.  
Operation  
Push the Control knob towards right  
or left.  
4 Exit Illumination Color Preset Recall mode  
Select the character type*  
Select the characters  
Press the Control knob.  
Turn the Control knob or push it  
towards up or down.  
Press the [FNC] button.  
* Each time you press the knob, the character type  
alternates between the types shown in the table below.  
When you recall Illumination Color Preset, the current  
Illumination Color settings will be replaced with the  
preset selection.  
Character type  
Alphabet upper case  
Alphabet lower case  
Numbers and symbols  
Special characters (Accent characters)  
Enter characters by using a remote control with numbers  
buttons.  
Example: If you are entering “DANCE.  
“D”  
[3]  
1
“A”  
[2]  
1
“N”  
[6]  
2
“C”  
[2]  
3
“E”  
[3]  
2
Character  
Button  
Times pressed  
[
¢
]
[
¢
]
[
¢
]
[
¢
]
5 Exit Menu mode  
Press the [FNC] button.  
A title cannot be attached to Audio file media.  
When operation stops for 10 seconds the name at that  
time is registered, and Name Set mode closes.  
Media that you can attach a name to  
- Internal CD player: 10 discs  
- External CD changer/ player: Varies according to the  
CD changer/ player. Refer to the CD changer/ player  
manual.  
You can change the name of a CD by the same  
operation you used to name it.  
English  
|
11  
 
Display Settings  
Auxiliary Input Display Setting  
Opening message edit  
Selects the display below when changing to  
Auxiliary input source.  
Setting the opening message to be displayed when  
the power is turned on.  
1 Select Auxiliary input display setting item  
during Menu mode (In AUX mode)  
Select the “Name Set” display.  
1 Select Opening message edit item during  
Menu mode  
Select “OPENING MSGE Edit.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
2 Enter Auxiliary input display setting mode  
Press the Control knob for at least 1 second.  
The presently selected Auxiliary input display is  
displayed.  
2 Enter Opening message edit mode  
Press the Control knob for at least 1 second.  
3 Enter the character  
Operation type  
Operation  
3 Select the Auxiliary input display  
Turn the Control knob or push it towards up or  
down.  
Move the cursor to the enter  
character position  
Push the Control knob towards right  
or left.  
Select the character type*  
Select the characters  
Press the Control knob.  
Turn the Control knob or push it  
towards up or down.  
“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”  
4 Exit Auxiliary input display setting mode  
* Each time you press the knob, the character type  
alternates between the types shown in the table below.  
Press the [FNC] button.  
Character type  
Alphabet upper case  
Alphabet lower case  
Numbers and symbols  
When operation stops for 10 seconds, the name at that  
time is registered, and the Auxiliary input display setting  
mode closes.  
The Auxiliary input display can be set only when the  
built-in auxiliary input or the auxiliary input of optional  
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is  
displayed by default.  
4 Press the Control knob for at least 2 seconds.  
“Completed” is displayed.  
5 Exit Menu mode  
Press the [FNC] button.  
The Opening message can be displayed up to 8  
characters.  
|
12 DPX503U/DPX303/DPX313  
 
Music disc/Audio file Operation  
Function of Audio file/ Internal CD source  
Function of remote control  
Music Select  
Direct Music Search  
Selecting the music you want to listen to from the  
device or media being played now.  
Searchs the music by entering the track number.  
1 Enter the music number  
Press the number buttons on the remote  
control.  
1 Enter Music Select mode  
Turn the Control knob.  
The music list is displayed.  
2 Search the music  
2 Search for music  
Press the [4] or [¢] button.  
Select the category item using the Control  
knob.  
Cancelling Direct Music Search  
Press the [38] button.  
iPod source (when “iPod Mode” is “ON”)  
(Function of DPX503U)  
Direct Music Search cannot be performed during playing  
of iPod, “Music Editor” media, Random play, or scan play.  
Operation type  
Operation  
Movement between items Turn the Control knob.  
Selection of item  
Press the Control knob.  
Return to previous item  
Return to first item  
Push the Control knob towards up.  
Push the Control knob towards up for at  
least 1 second.  
Function of disc changers with remote control  
Direct Disc Search  
Searchs the disc by entering the disc number.  
Other source  
Audio file (including iPod source while “iPod  
Mode” is “OFF”)  
1 Enter the disc number  
Press the number buttons on the remote  
control.  
Operation type  
Operation  
Movement between items Turn the Control knob or push it towards  
2 Search the disc  
up or down.  
Press the [FM] or [AM] button.  
Selection of item  
Return to previous item  
Return to first item  
Push the Control knob towards right.  
Push the Control knob towards left.  
Push the Control knob towards left for at  
least 1 second.  
Cancelling Direct Disc Search  
Press the [38] button.  
Internal CD source  
Direct Disc Search cannot be performed during playing  
of Random play or scan play.  
Operation type  
Operation  
Movement between track Turn the Control knob or push it towards  
up or down.  
Selection of track  
Press the Control knob.  
Return to first track  
Push the Control knob towards left for at  
least 1 second.  
The “2” or “3” symbol shown beside the displayed  
item indicates that the item is preceded or followed  
by another item.  
Selecting a music will play it from the beginning.  
Cancelling Music Select  
Press the [FNC] button.  
Music Select cannot be performed during Random play.  
Set the iPod mode in “MENU” > “iPod Mode” of  
<Function Control> (page 6).  
English  
|
13  
 
Music disc/Audio file Operation  
Basic Operation of Disc Changer  
(Optional)  
Selecting CD changer source  
Press the [SRC] button.  
Select the “CD Changer” display.  
For how to select source item, refer to <Power/  
Source Select button> of <Basic Operation> (page  
4).  
Music search  
Push the Control knob towards right or left.  
Disc Search  
Push the Control knob towards up or down.  
Playing the Current Song or Disc Repeatedly.  
(Repeat play)  
Press the [4] button.  
Pressing the button repeatedly selects Track Repeat  
play on (“Track Repeat ON”), Disc Repeat play on  
(“Disc Repeat ON”), and Repeat play off (“Repeat  
OFF”) sequentially.  
Randomly plays the music in the disc changer.  
(Magazine random play)  
Press the [6] button.  
Pressing the button toggles the setting between  
Magazine random play on (“Magazine RDM ON”)  
and off (“Magazine RDM OFF”).  
|
14 DPX503U/DPX303/DPX313  
 
Tuner Operation  
Function of remote control  
Station Preset Memory  
Putting a station in the memory.  
Direct Access Tuning  
Entering the frequency and tuning.  
1 Select the frequency to put in the memory  
Push the Control knob towards right or left.  
1 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote  
control.  
2 Enter Preset Memory mode  
Select “P.MEM.  
For how to select Function Control item, refer to  
“– – – –” is displayed.  
<Function Control> (page 6).  
2 Enter the frequency  
Press the number buttons on the remote  
3 Select the number to put in the memory  
control.  
Example:  
Turn the Control knob.  
4 Determine the number to put in the memory  
Desired frequency Press button  
Press the Control knob.  
92.1 MHz (FM)  
[0], [9], [2], [1]  
5 Allow the determined number to take effect  
810 kHz (AM)  
[0], [8], [1], [0]  
Press the Control knob.  
Cancelling Direct Access Tuning  
Press the [DIRECT] button on the remote  
control.  
Cancelling the Preset Memory mode  
Press the [FNC] button.  
This function can be operated with [1] — [6] button.  
Refer to <Basic operation> (page 4).  
You can enter the FM band frequency in steps of a  
minimum of 0.1 MHz.  
Preset Tuning  
Recalling the stations in the memory.  
Changing Language for PTY Function  
Selecting the Program Type display language as  
follows;  
1 Enter Preset Tuning Select mode  
Turn the Control knob.  
A station list is displayed.  
Language  
English  
Spanish  
French  
Display  
“English”  
“Spanish”  
“French”  
“Dutch”  
Language  
Norwegian  
Portuguese  
Swedish  
Display  
“Norwegian”  
“Portuguese”  
“Swedish”  
“German”  
2 Select a desired station in the memory  
Turn the Control knob.  
Dutch  
German  
3 Recall the station  
Press the Control knob.  
1 Enter PTY mode  
Refer to <PTY (Program Type)> (page 16).  
Cancelling Preset Tuning  
Press the [FNC] button.  
2 Enter Changing Language mode  
Press the [TI] button.  
This function can be operated with [1] — [6] button.  
Refer to <Basic operation> (page 4).  
3 Select the language  
Turn the Control knob or push it towards up or  
down.  
4 Exit Changing Language mode  
Press the [TI] button.  
English  
|
15  
 
Tuner Operation  
PTY (Program Type)  
Program Type preset  
Selecting the Program Type below and searching  
for a station;  
Putting the Program Type in the Preset button  
memory and quick recall.  
Program Type Display  
Program Type Display  
Presetting the Program Type  
Speech  
Music  
News  
“All Speech”  
“All Music”  
“News”  
Weather  
“Weather &  
Metr”  
1 Select the Program Type to preset  
Refer to <PTY (Program Type)> (page 16).  
Finance  
Children’s  
programs  
“Finance”  
“Children's  
Prog”  
Current Affairs “Current Affairs”  
2 Enter Program Type preset mode  
Information  
Sport  
“Information”  
“Sport”  
Press the [FNC] button.  
Social Affairs “Social Affairs”  
3 Select the number you want to put in the  
Religion  
Phone In  
Travel  
“Religion”  
“Phone In”  
“Travel &  
Touring”  
Education  
Drama  
“Education”  
“Drama”  
memory  
Turn the Control knob or push it towards left  
or right.  
Culture  
“Cultures”  
Science  
“Science”  
Leisure  
“Leisure &  
Hobby”  
Varied  
Pop Music  
Rock Music  
“Varied Speech”  
“Pop Music”  
“Rock Music”  
4 Preset the Program Type  
Press the Control knob for at least 1 second.  
Jazz Music  
“Jazz Music”  
Country Music “Country Music”  
National Music “National  
Music”  
5 Exit Program Type preset mode  
Easy Listening “Easy Listening  
Music M”  
Light Classical “Light Classic  
M”  
Serious Classical “Serious  
Classics”  
Press the [FNC] button.  
Recalling the preset Program Type  
Oldies Music “Oldies Music”  
Folk Music  
“Folk Music”  
1 Enter PTY mode  
Documentary “Documentary”  
Refer to <PTY (Program Type)> (page 16).  
Other Music  
“Other Music”  
2 Enter Program Type preset mode  
Speech and Music include the Program type shown  
below.  
Press the [FNC] button.  
3 Select the number you want to recall from the  
Music: Black character item.  
Speech: White character item.  
memory  
Turn the Control knob or push it towards left  
or right.  
1 Enter PTY mode  
Press the Control knob.  
“PTY Select” is displayed.  
4 Recall the Program Type  
Press the Control knob.  
2 Select the Program Type  
Turn the Control knob or push it towards up or  
down.  
5 Exit Program Type preset mode  
Press the [FNC] button.  
3 Search for the selected Program Type station  
Push the Control knob towards right or left.  
4 Exit PTY mode  
Press the Control knob.  
This function cannot be used during a traffic bulletin or  
AM reception.  
When the selected Program Type is not found, “No PTY”  
is displayed. Select another Program Type.  
|
16 DPX503U/DPX303/DPX313  
 
Other Functions  
Activating Security Code  
Deactivating Security Code  
To deactivate the Security Code function.  
You can set the Security Code with a 4 digit number of your  
choice.  
1 Select Security Code item during Menu  
mode (In Standby mode)  
Select the “Security Clear” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
The Security Code cannot be displayed or referenced. Make  
a note of the Security Code and treasure it up.  
1 Select Security Code item during Menu  
mode (In Standby mode)  
“Security Set” is displayed.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
2 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When “Enter” is displayed, “SECURITY CLEAR” is also  
displayed.  
2 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When “Enter” is displayed, “SECURITY SET” is also  
displayed.  
3 Enter Security Code  
Operation type  
Select the digits to enter  
Operation  
Push the Control knob towards right  
or left.  
Turn the Control knob or push it  
towards up or down.  
3 Enter Security Code  
Select the Security Code  
numbers  
Operation type  
Operation  
Select the digits to enter  
Push the Control knob towards right  
4 Press the Control knob for at least 3 seconds.  
“Clear” is displayed.  
The Security Code function deactivates.  
or left.  
Select the Security Code  
numbers  
Turn the Control knob or push it  
towards up or down.  
5 Exit Security Code mode  
4 Confirm the Security Code  
Press the [FNC] button.  
Press the Control knob for at least 3 seconds.  
When “Re-Enter” is displayed, “SECURITY SET” is also  
displayed.  
If a wrong security code is entered, “Error” is displayed.  
Enter a correct security code.  
5 Do the step 3 through 4 operation, and reenter  
the Security Code.  
“Approved” is displayed.  
The Security Code function activates.  
If you enter the wrong Code in steps 3 through 4, repeat  
from step 3.  
6 Exit Security Code mode  
Press the [FNC] button.  
Entering Security Code  
The Security Code is required to use the audio unit  
when the unit is first used after removed from the  
battery power source or the Reset button is pressed.  
1 Turn the power ON.  
2 Do the step 3 through 4 operation, and enter  
the Security Code.  
“Approved” is displayed.  
Now, you can use the unit.  
English  
|
17  
 
Other Functions  
Manual Clock Adjustment  
Demonstration mode setting  
Turning the demonstration mode ON/OFF.  
1 Select Clock Adjustment item during Menu  
mode  
Select the “Clock Adjust” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
1 Select Demonstration item during Menu mode  
Select the “DEMO Mode” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
2 Enter Clock adjustment mode  
Press the Control knob for at least 1 second.  
The clock display blinks.  
2 Set the Demonstration mode  
Press the Control knob for at least 2 seconds.  
Pressing this button for 2 seconds or longer toggles  
the setting between “ON” and “OFF.  
3 Adjusting Clock  
3 Exit Demonstration mode  
Operation type  
Selecting the item (hours or  
minutes)  
Operation  
Push the Control knob towards right  
or left.  
Press the [FNC] button.  
Adjust each item  
Turn the Control knob or push it  
towards up or down.  
When LX AMP unit connecting  
4 Exit Clock adjustment mode  
AMP Control  
You can control the LX AMP connected to the unit.  
Press the [FNC] button.  
You can do this adjustment when “MENU” > “SYNC” in  
1 Select AMP Control item during Menu mode  
Select the “AMS Control” display.  
<Function Control> (page 6) is set to “OFF.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
2 Enter AMP Control mode  
Date Adjustment  
Press the Control knob for at least 1 second.  
3 Select the AMP Control item for adjustment  
1 Select Date Adjustment item during Menu  
mode  
Push the Control knob towards up or down.  
Select the “Date Adjust” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
For the details on the AMP Control item, see the  
Instruction manual attached to the LX AMP.  
2 Enter Date adjustment mode  
Press the Control knob for at least 1 second.  
The date display blinks.  
4 Adjust the AMP Control item  
Push the Control knob towards right or left.  
5 Exit AMP Control mode  
3 Adjusting Date  
Press the [FNC] button.  
Operation type  
Operation  
Selecting the item (month, day, Push the Control knob towards right  
or year)  
or left.  
Adjust each item  
Turn the Control knob or push it  
towards up or down.  
4 Exit Date adjustment mode  
Press the [FNC] button.  
|
18 DPX503U/DPX303/DPX313  
 
Audio Adjustments  
Function of DPX503U  
Function of DPX503U  
Cabin selection  
DTA (Digital Time Alignment) setting  
You can compensate the delay of the sound arrival  
time, which is caused by the installation position of  
the speakers, by selecting your environment from  
the following car types;  
Adjusting fine tuning of the speaker position  
compensation value specified at <Cabin selection>  
(page 19).  
1 Enter DTA setting mode  
Car type (rear speaker position)  
Not compensating.  
Display  
“OFF”  
Select “SOUND” > “S-SET” > “DTA.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
Compact car (rear door)  
Compact car (cargo)  
Sedan (rear door)  
“Compact1”  
“Compact2”  
“Sedan1”  
“Sedan2”  
“Wagon1”  
“Wagon2”  
“Minivan1”  
“Minivan2”  
“SUV1”  
2 Select the speaker you want to set  
Sedan (cargo)  
Setting speaker  
Front speaker  
Rear speaker  
Subwoofer  
Display  
Station wagon (rear door)  
Station wagon (cargo)  
Minivan (rear door)  
“DTA-Front”  
“DTA-Rear"  
“DTA-Sub"  
Minivan (cargo)  
Turn the Control knob and push the center  
when the desired item is displayed.  
Sport-utility vehicle (rear door)  
Sport-utility vehicle (cargo)  
Passenger van (rear door)  
Passenger van (cargo)  
“SUV2”  
“PassengerVan1”  
“PassengerVan2”  
“User”  
3 Set the compensation value of the speaker  
position  
Turn the Control knob.  
Calls the value adjusted at <DTA> (page 19).  
Adjust between 0 and 440 cm.  
Refer to <Appendix> (page 29) on how to set the  
compensation value.  
1 Enter Cabin select mode  
Select “SOUND” > “S-SET” > “CABIN.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
4 Exit DTA setting mode  
Press the [FNC] button.  
2 Select the car type  
Turn the Control knob and push the center  
when the desired item is displayed.  
3 Exit Cabin select mode  
Press the [FNC] button.  
You can compensate the distances in more details by  
using <DTA> (page 19) function.  
In addition, the value specified at <DTA> can be called  
by selecting “User.  
English  
|
19  
 
Audio Adjustments  
Function of DPX503U  
2 Select the item you want to set  
Turn the Control knob and push the center  
when the desired item is displayed.  
X’Over setting  
You can set a X’Over value for the speakers;  
3 Set the value  
Adjustment Item Display  
Front High Pass Filter “HPF-Front”  
Range  
Through/40/60/80/100/120/  
150/180/220 Hz  
Through/40/60/80/100/120/  
150/180/220 Hz  
Turn the Control knob.  
4 Exit Equalizer Control mode  
Rear High Pass Filter “HPF-Rear”  
Press the [FNC] button.  
Low Pass Filter  
“LPF”  
50/60/80/100/120/Through  
Hz  
Subwoofer level  
Subwoofer Phase  
“SUB-W LEVEL 15 — +15  
“SW PHASE” Reverse (180°)/ Normal (0°)  
Function of DPX503U  
Preset position selection  
According to the listening position, select the  
position from the following settings so that the  
normal position of the sound environment can  
be compensated in accordance with the selected  
position;  
1 Enter X’Over setting mode  
Select “SOUND” > “S-SET” > “XOVER.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
2 Select the item you want to set  
Turn the Control knob and push the center  
when the desired item is displayed.  
Compensation seat  
Not compensating.  
Front-Left seat  
Range  
“All”  
“FrontLeft”  
“FrontRight”  
“FrontAll”  
“USER”  
3 Set the X’Over value  
Front-Right seat  
Front seat  
Turn the Control knob.  
4 Exit X’Over setting mode  
Calls the value adjusted at <Manual position  
setting> (page 21).  
Press the [FNC] button.  
1 Enter Position setting mode  
Select “SOUND” > “S-CTRL> “POSIT” > “P-POSI.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
Function of DPX503U  
Equalizer Control  
You can adjust following Equalizer Control items ;  
2 Select the seat you want to compensate  
Turn the Control knob.  
Adjustment Item Display  
Range  
System Q  
“Preset EQ”  
“NATURAL(Natural)/“USER”  
(User setting)/“ROCK”(Rock)/  
“POPS”(Pops)/“EASY”(Easy)/  
“TOP40”(Top 40)/JAZZ”  
(Jazz)/ ”GAME”(Game)  
–8 — +8  
3 Exit Position setting mode  
Press the [FNC] button.  
Bass level*  
“Bass”  
Middle level*  
Treble level*  
“Middle”  
“Treble”  
–8 — +8  
–8 — +8  
* Source tone memory: Puts the set up value in the  
memory per source.  
“USER”: The ranges selected lastly for Bass level, Middle  
level, and Treble level are recalled automatically.  
1 Enter Equalizer Control mode  
Select “SOUND” > “S-CTRL> “EQ.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
|
20 DPX503U/DPX303/DPX313  
 
Function of DPX503U  
Function of DPX503U  
Manual position setting  
Audio Preset Memory  
Making fine adjustment of the value specified at  
Preset position selection per speaker.  
Registering the value setup by Sound Control. The  
memory cannot be erased by the Reset button.  
1 Enter Position setting mode  
Select “SOUND” > “S-CTRL> “POSIT” >  
“M-POSI.  
1 Setup Sound Control  
Refer to the following operations to setup the  
Sound Control.  
For how to select Function Control item, refer to  
- Cabin selection (page 19)  
<Function Control> (page 6).  
- DTA (Digital Time Alignment) setting (page 19)  
- X’Over setting (page 20)  
- Equalizer Control (page 20)  
- Preset position selection (page 20)  
- Manual position setting (page 21)  
2 Select the speaker you want to adjust  
Item  
Setting overview  
Front Left speaker  
Front Right speaker  
Rear Left speaker  
Rear Right speaker  
Subwoofer Left  
“Front Lch”  
“Front Rch”  
“Rear Lch”  
“Rear Rch”  
“Sub Lch”  
“Sub Rch”  
2 Enter Audio Preset Memory mode  
Select “SOUND” > “PRESET” > “MEMO.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
Subwoofer Right  
3 Put the Audio Preset in the memory  
Press the Control knob.  
“Memory?” is displayed.  
Turn the Control knob and push the center  
when the desired item is displayed.  
3 Adjust the speaker  
4 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Memory Completed” is displayed.  
Turn the Control knob.  
Adjust between 0 and 170 cm.  
4 Exit Position setting mode  
5 Exit Audio Preset mode  
Press the [FNC] button.  
Press the [FNC] button.  
When you select “User” at <Preset position selection>  
(page 20), the adjusted setting value will be recalled.  
Register 1 pair of Audio Preset Memory. You cannot  
register by the source.  
When you press the Reset, all the sources will be the  
setting value which is registered.  
English  
|
21  
 
Audio Adjustments  
Function of DPX503U  
Audio Control  
You can adjust following Audio Control items ;  
Audio Preset Recall  
Recalling the sound setup registered by <Audio  
Preset Memory> (page 21).  
Adjustment Item Display  
Rear volume “REAR VOLUME” 0 — 35  
Subwoofer level* “SUB-W LEVEL 15 — +15  
Range  
1 Select the source  
System Q*  
“NATURAL/  
Natural/User setting/Rock/  
For how to select source item, refer to <Power/  
Source Select button> of <Basic Operation> (page  
4).  
“USER”/“ROCK”/ Pops/Easy/Top 40/Jazz/Game  
“POPS”/“EASY”/  
“TOP40”/“JAZZ”/  
”GAME”  
2 Enter Audio Preset Recall mode  
Select “SOUND” > “PRESET” > “RECALL”.  
For how to select Function Control item, refer to  
<Function Control> (page 6).  
Bass level*  
Middle level*  
Treble level*  
Balance  
“BASS LEVEL”  
“MIDDLE LEVEL 8 — +8  
“TREBLE LEVEL 8 — +8  
“BALANCE”  
“FADER”  
–8 — +8  
Left 15 — Right 15  
Rear 15 — Front 15  
3 Recall the Audio Preset  
Press the Control knob.  
“Recall?” is displayed.  
Fader  
Exit Audio Control mode (Volume control mode)  
*Function of DPX303/DPX313.  
4 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Recall Completed” is displayed.  
Source tone memory: You can set Bass, Middle, and  
Treble for each source.  
“USER”: The ranges selected lastly for Bass level, Middle  
level, and Treble level are recalled automatically.  
5 Exit Audio Preset Recall mode  
Press the [FNC] button.  
1 Select the source to adjust  
For how to select source item, refer to <Power/  
Source Select button> of <Basic Operation> (page  
4).  
The User memory of “SYSTEM Q” in <Equalizer Control>  
(page 20) is changed to the value which was recalled.  
The source tone memory item of <Equalizer Control>  
(page 20) is changed to the value which was recalled by  
the selected source.  
2 Enter Audio Control mode  
Press the [AUD] knob.  
3 Select the Audio item to adjust  
Press the [AUD] knob.  
4 Adjust the Audio item  
Turn the [AUD] knob.  
5 Exit Audio Control mode  
Press any button.  
Press a button other than the [AUD] knob or [0]  
and [ATT] button.  
|
22 DPX503U/DPX303/DPX313  
 
Audio Setup  
Speaker Setting  
You can set Sound system , such as follows;  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type as follows;  
Adjustment Item Display  
Range  
Front High Pass Filter* “HPF-F”  
Through/40/60/80/100/120/  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Display  
“OFF”  
“5/4inch”  
“6x9/6inch”  
“O.E.M.”  
150/180/220 Hz  
Rear High Pass Filter* “HPF-R”  
Through/40/60/80/100/120/  
150/180/220 Hz  
50/60/80/100/120/Through  
Hz  
Low Pass Filter*  
“LPF”  
Subwoofer Phase* “SW PHASE” Reverse (180°)/ Normal (0°)  
1 Enter Standby  
Volume offset  
Loudness*  
Dual Zone System  
“VOL-OFFSET” –8 — 0 (AUX: -8— +8)  
Select the “STANDBY” display.  
“LOUD”  
OFF/ON  
OFF/ON  
For how to select source item, refer to <Power/  
Source Select button> of <Basic Operation> (page  
4).  
“2 ZONE”  
*Function of DPX303/DPX313.  
2 Enter Speaker Setting mode  
Press the [AUD] knob.  
“SP SELis displayed.  
Volume offset: Sets each source’s volume as a difference  
from the basic volume.  
Loudness: Compensates for low and high tones during  
low volume. (Only the low tone is compensated for  
when the tuner is selected as a source.)  
Dual Zone System  
3 Select the Speaker type  
Turn the [AUD] knob.  
4 Exit Speaker Setting mode  
Main source and sub source (Auxiliary input) output  
Front channel and Rear channel separately.  
- Set up the channel of sub source by “Zone2” of  
<Function Control> (page 6).  
Press the [AUD] knob.  
- Select Main source by [SRC] button.  
- Adjust the volume of Front channel by [AUD] knob.  
- Adjust the volume of Rear channel by <Audio Control>  
(page 22) or [5]/[] button on the remote control  
(page 25).  
- The Audio Control has no effect on sub source.  
1 Select the source to adjust  
For how to select source item, refer to <Power/  
Source Select button> of <Basic Operation> (page  
4).  
2 Enter Audio Setup mode  
Press the [AUD] knob for at least 1 second.  
3 Select the Audio Setup item to adjust  
Press the [AUD] knob.  
4 Adjust the Audio setup item  
Turn the [AUD] knob.  
5 Exit Audio Setup mode  
Press the [AUD] knob for at least 1 second.  
English  
|
23  
 
Audio Adjustments  
Function of DPX303/DPX313  
Function of DPX303/DPX313  
Audio Preset Memory  
Audio Preset Recall  
Registering the value setup by Sound Control. The  
memory cannot be erased by the Reset button.  
Recalling the sound setup registered by <Audio  
Preset Memory> (page 24).  
1 Setup Sound Control  
Refer to the following operations to setup the  
Sound Control.  
- <Audio Control> (page 22)  
- <Audio Setup> (page 23)  
1 Select the source  
For how to select source item, refer to <Power/  
Source Select button> of <Basic Operation> (page  
4).  
2 Select Audio Preset item during Menu  
mode (Other than Standby mode)  
Select the “Audio Preset” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
2 Select Audio Preset item during Menu  
mode (Other than Standby mode)  
Select the “Audio Preset” display.  
For how to select Function Control items, refer to  
<Function Control> (page 6).  
3 Enter Audio Preset mode  
3 Enter Audio Preset mode  
Press the Control knob for at least 1 second.  
Press the Control knob for at least 1 second.  
4 Select the Audio Preset Recall  
Turn the Control knob.  
Select the “Recall” display.  
4 Select the Audio Preset Memory  
Turn the Control knob.  
Select the “Memory” display.  
5 Determine whether to recall the Audio Preset  
Press the Control knob.  
“Recall?” is displayed.  
5 Determine whether to put the Audio Preset in  
the memory  
Press the Control knob.  
“Memory?” is displayed.  
6 Recall the Audio Preset  
Turn the Control knob to select “YES, and then  
press the Control knob.  
6 Put the Audio Preset in the memory  
Turn the Control knob to select “YES, and then  
press the Control knob.  
“Recall Completed” is displayed.  
7 Exit Audio Preset mode  
“Memory Completed” is displayed.  
Press the [FNC] button.  
7 Exit Audio Preset mode  
Press the [FNC] button.  
The User memory of “SYSTEM Q” in <Audio Control>  
(page 22) is changed to the value which was recalled.  
The source tone memory item of <Audio Control> (page  
22) is changed to the value which was recalled by the  
selected source.  
Register 1 pair of Audio Preset Memory. You cannot  
register by the source.  
When you press the Reset, all the sources will be the  
setting value which is registered.  
The following items cannot be registered.  
Volume, Balance, Fader, Loudness, Volume offset, Dual  
Zone System, Rear Volume  
|
24 DPX503U/DPX303/DPX313  
 
Accessory of DPX503U/DPX313  
Basic Operations of remote control  
In Tuner source  
SRC  
ATT  
VOL  
AUD  
SRC  
AT T  
Band select  
[FM]/[AM]  
VOL  
AUD  
Station select  
[4]/[¢]  
Recall preset stations  
[1] — [6]  
FM/AM  
2-ZONE  
0 — 9  
DIRECT  
(page 15)  
In CD/USB source  
Music select  
[4]/[¢]  
Folder/Disc select  
Pause/Play  
[FM]/[AM]  
[38]  
About [  
]
General control  
This button is used when Bluetooth HANDS FREE  
BOX is connected. For more information, refer to the  
instruction manual of Bluetooth HANDS FREE BOX.  
Volume control  
Source select  
[VOL]  
[SRC]  
[ATT]  
¤
• Do not set the remote control in hot places such as  
on the dashboard.  
Volume reduce  
In Audio control  
Loading and Replacing battery  
Use two “AA”/ “R6”-size batteries.  
Slide the cover while pressing downwards to remove  
it as illustrated.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
Audio item select  
[AUD]  
[VOL]  
Adjusts the Audio item  
Refer to <Audio Control> (page 22) for the operation  
method, such as the procedures for Audio control and  
others operations.  
Dual Zone control  
Dual zone system on and off  
Rear channel volume control  
[2-ZONE]  
[ 5]/ []  
English  
|
25  
 
Appendix  
About Audio file  
About USB device  
Playable Audio file  
• If you start playback after connecting the iPod, the  
music that has been played by the iPod is played  
first.  
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)  
Playable disc media  
CD-R/RW/ROM  
Playable disc file format  
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.  
USB device Playable Model  
DPX503U  
Playable USB device  
USB mass storage class  
Playable USB device file system  
FAT16, FAT32  
In this case, “RESUMING” is displayed without  
displaying a folder name, etc. Changing the browse  
item will display a correct title, etc.  
• When the iPod is connected to this unit,  
“KENWOOD” or “” is displayed on the iPod to  
indicate that you cannot operate the iPod.  
• When the USB device is connected to this unit,  
it can be charged up provided that this unit is  
powered.  
• Install the USB device in the place where it will not  
prevent you from driving your vehicle properly.  
• You cannot connect a USB device via a USB hub and  
Multi Card Reader.  
• Take backups of the audio files used with this unit.  
The files can be erased depending on the operating  
conditions of the USB device.  
We shall have no compensation for any damage  
arising out of erasure of the stored data.  
• No USB device comes with this unit. You need to  
purchase a commercially available USB device.  
Although the audio files are complied with the  
standards listed above, the play maybe impossible  
depending on the types or conditions of media or  
device.  
Playing order of the Audio file  
In the example of folder/file tree shown below, the  
files are played in the order from to .  
<
v
:
Folder
Audiofile  
CD  
()  
:
vꢀ  
• When connecting the USB device, usage of the CA-  
U1EX (option) is recommended.  
Normal playback is not guaranteed when a cable  
other than the USB compatible cable is used.  
Connecting a cable whose total length is longer  
than 5 m can result in abnormal playback.  
vꢆ  
vꢇ  
vꢄ  
vꢉ  
v.  
About KENWOOD “Music Editor” of PC  
application  
An online manual about audio files is put on the  
site, www.kenwood.com/audiofile/. On this online  
manual, detailed information and notes which are not  
written in this manual are provided. Make sure to read  
through the online manual as well.  
• “Music Editor” is recorded in the CD-ROM attached  
to this unit.  
• Refer to the user’s manual recorded in the  
installation CD-ROM and Help of “Music Editor” for  
the operation method of “Music Editor.  
• The unit can play USB device created by “Music  
Editor.  
In this manual, the word “USB device” is used for flash  
memories and digital audio players which have USB  
terminals.  
• Information about “Music Editor” upgrade is put on  
The word “iPod” appearing in this manual indicates the  
iPod connected with the iPod connection cable (optional  
accessory). The iPod connected with the iPod connection  
cable can be controlled from this unit. iPods that can be  
connected with the iPod connection cable are the iPod  
nano, Fifth Generation iPod, iPod classic, and iPod touch.  
Other iPods cannot be connected.  
|
26 DPX503U/DPX303/DPX313  
 
For operating KCA-BT100 (Optional)  
However, the following control methods of the  
function for this unit may be different from the  
Instruction manual; therefore, refer to the following  
supplemental instruction.  
<Deleting a Registered Cell-Phone>  
1–3. Operation is the same. Refer to the instruction  
manual of KCA-BT100.  
4. Press the Control knob.  
5. Select “YES” using the Control knob.  
6. Press the Control knob.  
7. Press the [FNC] button.  
<Menu System>  
For how to operate Menu, refer to <Function  
Control> in this instruction manual.  
About display  
Function Control Glossary  
SRC Select  
Setting up the Source Select mode.  
1 : Displays source icons for your choice.  
2 : Allows you to select sources one after another.  
Display  
If this unit is not operated at least 5 seconds with  
“OFF” selected, the display turns off. During a setup  
mode, the display will not turn off even if 5 seconds  
lapse.  
ILM Dimmer (illumination dimmer)  
Reduces the key Illumination brightness.  
AUTO: Dims the illumination in conjunction with  
the Light switch of the vehicle.  
MNAL: Dims the illumination constantly.  
OFF: Does not dim the illumination.  
AT COL CHG (Automatic illumination color  
change)  
Cell-Phone Status is displayed in the status display of  
this unit.  
Moreover, some displays are different from the  
description of KCA-BT100 Instruction Manual.  
Selecting “iPod” changes the key illumination  
automatically according to the color of the iPod  
body during playback of the iPod source.  
* The color of key illumination is only a  
recommended color by our campany. It does not  
necessarily match the body color of iPod.  
Compatible iPod models:  
iPod (5th generation), iPod classic, iPod touch,  
iPod nano (1st/2nd/3rd generation),  
Fifth Generation iPod (iPod with video)  
Displays of KCA-BT100 Instruction Actual displays on this unit  
Manual  
“Disconnect”  
“HF Disconnect”  
“Connect”  
“HF Connect”  
“Phone Delete”  
“Phone Status”  
“Device Delete”  
“BT DVC Status”  
BT : Displays the bluetooth connection status.  
This indicator turns on when a cell-phone is  
connected to this unit.  
SWPRE (Switching Preout)  
Switches the preout between rear output (“Rear”)  
and subwoofer output (“Sub-W”).  
AMP  
Selecting “OFF” turns off the built-in amplifier.  
Turning off the built-in amplifier improves the  
quality of the sound from Preout.  
Selecting “OFF” disables the functions of the Dual  
Zone and KCA-BT100 (optional accessory) because  
no sound will be output from the front speakers.  
Zone2 (Dual Zone)  
Set the destination (front speaker “Front” or rear  
speaker “Rear”) of the sub source (AUX IN) when the  
Dual Zone function is turned on.  
Supreme  
Technology to extrapolate and supplement with  
proprietary algorithm, the high-frequency range  
that is cut off when encoding at low bit rate (less  
than 128Kbps, Sampling frequency is 44.1kHz).  
Supplementing is optimized by compression  
format (AAC, MP3 or WMA) and processed  
according to bit rate.  
The effect is negligible with music that is encoded  
at high bit rate, variable bit rate or has minimal high  
frequency range.  
English  
|
27  
 
Appendix  
News (News Bulletin with Timeout Setting)  
Automatically receives news bulletin when it  
starts. Set the time during which interrupt is to be  
disabled after start of another news bulletin.  
Changing “News 00min” to “News 90min” turns this  
function ON.  
If news bulletin starts when this function is ON,  
Traffic INFO” is displayed and news is received. If  
“20min” is has been set, reception of another news  
bulletin will not start for 20 minutes.  
The news bulletin volume is the same level that  
was set for Traffic Information.  
Seek Mode (Tuning mode select)  
Select a tuning mode of the radio.  
DISP REVERSE  
Switches the panel display between positive  
or negative. In addition, you can reverse it in  
conjunction with the interior light.  
POSI 1 : Displays the text in the positive.  
POSI 2 : When the interior light is off, the text is  
displayed in the positive; when the interior  
light is on, the text is displayed in the  
negative.  
NEGA 1 : Displays the text in the negative.  
NEGA 2 : When the interior light is off, the text  
is displayed in the negative; when the  
interior light is on, the text is displayed in  
the positive.  
Tuning mode  
Auto seek  
Display Operation  
“Auto1” Automatic search for a station.  
Cabin  
The position of front and rear speakers may not  
have the same distance from the center of the  
vehicle interior.  
For example, when a car type has the front speaker  
nearer to the center of the vehicle interior than the  
rear speaker, you hear a delayed sound from the  
rear speaker.  
This function allows the sound of the nearer  
speaker to the center of the vehicle interior to be  
output with delays and compensates the sound  
arrival time from the front and rear speakers to be  
heard at the same time.  
The sound arrival time can be compensated simply  
by selecting the car type you want to use, because  
the compensation values for typical cars have been  
preset.  
Preset station seek “Auto2” Search in order of the stations in the  
Preset memory.  
Manual  
“Manual” Normal manual tuning control.  
AF (Alternative Frequency)  
When the reception is poor, automatically alternate  
to another frequency broadcasting the same  
program in the same RDS network with better  
reception.  
Russian (Russian language setting)  
When this is set to ON, the following character  
strings are displayed in Russian:  
Folder name/ File name/ Song title/ Artist name/  
Album name/ KCA-BT100 (optional accessory)  
Power OFF (Power OFF Timer)  
Setting the timer to turn this unit’s power OFF  
automatically when Standby mode continues.  
Using this setting can save the vehicle’s battery  
power.  
– – –: Power OFF Timer function is OFF.  
20min: Turns the power OFF after 20 minutes.  
(Factory setting)  
You can specify the more suitable compensation  
values for your vehicle by using <DTA> (page 19)  
function.  
You can also compensate the listening positions  
(such as front and rear) in accordance with scenes  
by specifying the positions at <Preset position  
selection> (page 20).  
40min: Turns the power OFF after 40 minutes.  
60min: Turns the power OFF after 60 minutes.  
CD Read  
Sets the method for reading CD.  
When unable to play special format CD, set this  
function to “2” to force playing. Note that some  
music CD may be unplayable even when set to “2.  
In addition, audio files cannot be played when set  
to “2. Normally, keep this set to “1.  
1 : Automatically distinguishes between audio file  
disc and music CD when playing disc.  
2 : Forces playing as music CD.  
|
28 DPX503U/DPX303/DPX313  
 
DTA (Digital Time Alignment)  
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
Make fine adjustment of the delay time of the  
speaker output specified at <Cabin selection>  
(page 19) to have a more suitable environment for  
your vehicle.  
Information on Disposal of Old Electrical  
and Electronic Equipment and Batteries  
(applicable for EU countries that have  
adopted separate waste collection systems)  
Products and batteries with the symbol  
(crossed-out wheeled bin) cannot be  
disposed as household waste.  
The settings of the delay time are automatically  
identified and compensated by specifying the  
distances of each speaker from the center of the  
vehicle interior.  
1 Set the front and rear positions and the height  
of the reference point to the position of the ears  
of the person sitting in the front seat, and set  
the right and left positions to the center of the  
vehicle interior.  
Old electrical and electronic equipment  
and batteries should be recycled at a facility  
capable of handling these items and their  
waste byproducts.  
2 Measure the distances from the reference point  
to the speakers.  
Contact your local authority for details in  
locating a recycle facility nearest to you.  
Proper recycling and waste disposal will  
help conserve resources whilst preventing  
detrimental effects on our health and the  
environment.  
3 Calculate the distance difference in accordance  
with the farthest speaker.  
+100cm  
Notice: The sign "Pb" below the symbol for  
batteries indicates that this battery  
contains lead.  
FRONT  
REAR  
FRONT  
50cm  
80cm  
The marking of products using lasers  
(Except for some areas)  
REAR  
150cm  
+70cm  
CLASS 1  
LASER PRODUCT  
+0cm  
SUB-W  
The label is attached to the chassis/case and says  
that the component uses laser beams that have been  
classified as Class 1. It means that the unit is utilizing  
laser beams that are of a weaker class. There is no  
danger of hazardous radiation outside the unit.  
English  
|
29  
 
Accessories/ Installation Procedure  
Accessories  
¤
Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
1
Make sure to ground the unit to a negative 12V DC power  
supply.  
..........1  
..........2  
Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
Do not use your own screws. Use only the screws provided.  
If you use the wrong screws, you could damage the unit.  
If the power is not turned ON (“Protect” is displayed), the  
speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
2
Installation Procedure  
1. To prevent short circuits, remove the key from the  
ignition and disconnect the - terminal of the  
battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the wire on the wiring harness.  
4. Take Connector B on the wiring harness and  
connect it to the speaker connector in your vehicle.  
5. Take Connector A on the wiring harness and  
connect it to the external power connector on your  
vehicle.  
6. Connect the wiring harness connector to the unit.  
7. Install the unit in your car.  
8. Reconnect the - terminal of the battery.  
9. Press the reset button.  
Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not  
be linked with the ignition (i.e., it will not turn on and off  
along with the ignition). If you want to link the unit’s power  
with the ignition, connect the ignition wire to a power  
source that can be turned on and off with the ignition key.  
Use a commercially available conversion connector if the  
connector does not fit in the vehicle connector.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
If the console has a lid, make sure to install the unit so that  
the faceplate will not hit the lid when closing and opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with one  
with the same rating.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail to  
work if you share the - wires or ground them to any metal  
part in the car.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
About CD players/disc changers connected  
to this unit  
If the CD player/ disc changer has the “O-N” switch, set  
it to the “N” position.  
The functions you can use and the information that  
can be displayed may differ depending on the models  
being connected.  
|
30 DPX503U/DPX303/DPX313  
 
Connecting Wires to Terminals  
To External Display/ Steering remote  
FM/AM antenna input (JASO)  
Front preout  
Rear/SubWoofer preout  
Fuse (10A)  
To Kenwood disc changer/ External optional accessory  
To connect these leads, refer to the relevant instruction manuals.  
Wiring harness  
(Accessory1)  
TEL mute wire (Brown)  
Connect to the terminal that is grounded when  
either the telephone rings or during conversation.  
MUTE  
To connect the Kenwood navigation system,  
consult your navigation manual.  
If no connections are made, do not  
let the wire come out from the tab.  
Power control/ Motor antenna  
control wire (Blue/White)  
P.CONT  
Connect either to the power control terminal  
when using the optional power amplifier, or to the  
antenna control terminal in the vehicle.  
ANT.CONT  
Battery wire (Yellow)  
Ignition wire (Red)  
See next page.  
A–7 Pin (Red)  
A–4 Pin (Yellow)  
8
7
6
5
4
3
2
1
Connector A  
Connector B  
8
7
6
5
4
3
2
1
English  
|
31  
 
Connecting Wires to Terminals  
Connector Function Guide  
Pin Numbers for Cable Colour  
ISO Connectors  
External Power  
Connector  
2WARNING  
Functions  
Connecting the ISO Connector  
The pin arrangement for the ISO connectors depends on  
the type of vehicle you drive. Make sure to make the proper  
connections to prevent damage to the unit.  
A-4  
A-5  
A-6  
A-7  
A-8  
Yellow  
Battery  
Power Control  
Dimmer  
Ignition (ACC)  
Earth (Ground)  
Connection  
The default connection for the wiring harness is described in  
1 below. If the ISO connector pins are set as described in 2,  
make the connection as illustrated.  
Please be sure to reconnect the cable as shown 2 below to  
install this unit to the Volkswagen vehicles etc.  
Blue/White  
Orange/White  
Red  
Black  
Speaker  
Connector  
B-1  
B-2  
B-3  
B-4  
B-5  
B-6  
B-7  
1(Default setting) The A-7 pin (red) of the vehicle’s  
ISO connector is linked with the ignition, and the A-  
4 pin (yellow) is connected to the constant power  
supply.  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right (–)  
Front Right (+)  
Front Right (–)  
Front Left (+)  
Front Left (–)  
Rear Left (+)  
Rear Left (–)  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
B-8  
Green/Black  
2The A-7 pin (red) of the vehicle’s ISO connector is  
connected to the constant power supply, and the  
A-4 pin (yellow) is linked to the ignition.  
Ignition cable  
A-7 Pin (Red)  
(Red)  
Unit  
Vehicle  
A-4 Pin (Yellow)  
Battery cable  
(Yellow)  
|
32 DPX503U/DPX303/DPX313  
 
Installation/Removing the Unit  
Installation  
Removing the hard rubber frame  
1 Engage the catch pins on the removal tool and  
remove the two locks on the upper level.  
Upper the frame and pull it forward as shown in  
the figure.  
Lock  
Catch  
Accessory2  
Bend the tabs of the mounting sleeve with  
a screwdriver or similar utensil and attach it  
in place.  
2 When the upper level is removed, remove the  
lower two locations.  
The frame can be removed from the bottom side in the  
same manner.  
Make sure that the unit is installed securely in place. If the  
unit is unstable, it may malfunction (for example, the sound  
may skip).  
Removing the Unit  
1 Refer to the section <Removing the hard rubber  
frame> and then remove the hard rubber frame.  
2 Insert the two removal tools deeply into the slots  
on each side, as shown.  
3 Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
Accessory2  
¤
Be careful to avoid injury from the catch pins on the  
removal tool.  
4 Pull the unit all the way out with your hands, being  
careful not to drop it.  
English  
|
33  
 
Troubleshooting Guide  
Some functions of this unit may be disabled by  
some settings made on this unit.  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
!
• Cannot set up the subwoofer.  
• Cannot set up the High Pass Filter.  
• Cannot set up the Fader.  
General  
• No Audio control effect on AUX.  
• Cannot set up the subwoofer position of Manual  
position setting.  
? The Touch Sensor Tone does not sound.  
The preout jack is being used.  
The Touch Sensor Tone cannot be output from  
the preout jack.  
• Preout is not set to subwoofer. “MENU” >  
“SWPRE” of <Function Control> (page 6)  
• <Subwoofer output> of <Basic Operation> (page 4)  
is not set to On.  
• The Dual zone function is enabled. <Audio  
? The illumination flashes when the knob or button  
is operated.  
This is the key illumination effect.  
You set this effect in “MENU” > “ILM Effect” of  
Setup> (page 23)  
<Function Control> (page 6).  
!
!
• Cannot set up the subwoofer phase.  
The Low Pass Filter is set to Through. <Audio  
Setup> (page 23), <X’Over setting> (page 20)  
? The key illumination effect brought about in  
conjunction with the sound volume is small.  
The key illumination effect may be insufficient  
depending on the sound volume and sound quality.  
• Cannot select the output destination of the  
subsource in the Dual zone.  
• Cannot adjust the volume of the rear speakers.  
The Dual zone function is disabled. <Audio  
Setup> (page 23)  
Tuner source  
? Radio reception is poor.  
The car antenna is not extended.  
Pull the antenna out all the way.  
!
• Cannot register a security code.  
• Cannot set up Display Illumination Control.  
• Cannot set up the Power-off timer.  
<Demonstration mode Setting> (page 18) is not  
turned off.  
Disc source  
? The specified disc does not play, but another one  
plays instead.  
The specified CD is quite dirty.  
Clean the CD, referring to the CD cleaning of the  
section on <Handling CDs> (page 3).  
The disc is loaded in a different slot from that  
specified.  
Eject the disc magazine and check the number  
for the specified disc.  
The disc is severely scratched.  
Try another disc instead.  
Audio file source  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
Clean the media, referring to the CD cleaning of  
the section on <Handling CDs> (page 3).  
The recording condition is bad.  
Record the media again or use another media.  
? Noise is heard when carrying out Folder Search.  
Noise may be produced if folders without audio files  
exist continuously in the playing media.  
Do not make folders without audio files.  
|
34 DPX503U/DPX303/DPX313  
 
USB ERROR (Blink):  
Some trouble may have occurred to the  
The messages shown below display your  
systems condition.  
connected USB device.  
Remove the USB device, then cycle the  
power switch to ON. If the same display is  
repeated, use another USB device.  
TOC Error:  
• No disc has been loaded in the disc  
magazine.  
• The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
iPod Error:  
Connection to the iPod has failed.  
Check that the connected iPod is an iPod  
that is supported. See <About Audio file>  
(page 26) for information on supported  
iPods.  
Remove the USB device and then  
reconnect it.  
Error 05:  
Error 77:  
The disc is unreadable.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
“Error 77” code does not disappear, consult  
your nearest service center.  
Confirm that the software for the iPod is  
the latest version.  
Mecha Error/ Mecha ERR:  
Something is wrong with the disc magazine.  
Or the unit is malfunctioning for some reason.  
Check the disc magazine. And then press  
the reset button on the unit. If the “Mecha  
Error” code does not disappear, consult  
your nearest service center.  
USB REMOVE: The Remove mode has been selected for the  
USB device/iPod. You can remove the USB  
device/iPod safely.  
IN (Blink):  
Protect:  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and then  
the protection function is activated.  
Wire or insulate the speaker cable properly  
and press the reset button. If the “Protect”  
code does not disappear, consult your  
nearest service center.  
Unsupported File:  
An Audio file is played with a format that this  
unit can’t support.  
Copy Protect/ Copy Protection/ COPY PRO:  
A copy-protected file is played.  
Read Error:  
The file system of the connected USB device  
is broken.  
Copy the files and folders for the USB  
device again. If the error message is still  
displayed, initialize the USB device or use  
other USB devices.  
No Device:  
N/A Device:  
The USB device is selected as a source  
although no USB device is connected.  
Change the source to any source other  
than USB. Connect an USB device, and  
change the source to USB again.  
An unsupported USB device is connected.  
No Music Data/ No Music/ Error 15:  
• The connected USB device contains no  
playable audio file.  
• Media was played that does not have data  
recorded that the unit can play.  
English  
|
35  
 
Specifications  
FM tuner section  
USB Interface (DPX503U)  
Frequency range (50 kHz space)  
: 87.5 MHz – 108.0 MHz  
USB Standard  
: USB1.1/ 2.0  
Usable sensitivity (S/N = 26dB)  
: 0.7 μV/75 Ω  
Quieting Sensitivity (S/N = 46dB)  
: 1.6 μV/75 Ω  
Maximum Supply current  
: 500 mA  
File System  
: FAT16/ 32  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 65 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
Selectivity (DIN) ( 400 kHz)  
: ≥ 80 dB  
AAC decode  
: AAC-LC .m4a” files  
Stereo separation (1 kHz)  
: 35 dB  
Audio section  
Maximum output power  
: 50 W x 4  
MW tuner section  
Frequency range (9 kHz space)  
: 531 kHz – 1611 kHz  
Full Bandwidth Power (PWR DIN45324, +B=14.4V)  
: 30 W x 4  
Usable sensitivity (S/N = 20dB)  
Speaker Impedance  
: 25 μV  
: 4 – 8 Ω  
Tone action  
Bass : 100 Hz 8 dB  
Middle : 1 kHz 8 dB  
Treble : 10 kHz 8 dB  
Preout level / Load (CD)  
: 2500 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
LW tuner section  
Frequency range  
: 153 kHz – 281 kHz  
Usable sensitivity (S/N = 20dB)  
: 45 μV  
CD player section  
Laser diode  
Auxiliary input  
Frequency response ( 1 dB)  
: 20 Hz – 20 kHz  
Input Maximum Voltage  
: 1200 mV  
Input Impedance  
: 100 kΩ  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 24 Bit  
Spindle speed  
: 500 – 200 rpm (CLV)  
Wow & Flutter  
: Below Measurable Limit  
General  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Total harmonic distortion (1 kHz)  
: 0.008 %  
Signal to Noise ratio (1 kHz)  
: 105 dB  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 112 x 160 mm  
Dynamic range  
: 93 dB  
Weight  
: 1.6 kg  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC .m4a” files  
Specifications subject to change without notice.  
|
36 DPX503U/DPX303/DPX313  
 

Ingersoll Rand Laptop Docking Station 45532694 User Manual
Integra Stereo Receiver DHC 99 User Manual
Intel Computer Hardware AIMB 744 User Manual
Jensen MP3 Player SMP 1GBEB User Manual
Jet Tools Lathe JML 1220 User Manual
JVC Stereo Receiver 0303NHMMDWJEIN User Manual
Kawai Musical Instrument Amplifier A 15 User Manual
KitchenAid Cooktop KECC568RPB04 User Manual
KitchenAid Range KERC500 User Manual
KitchenAid Ventilation Hood kdrs505xss00 User Manual