Kenwood Car Stereo System DPX502U User Manual

DUAL DIN SIZED CD RECEIVER  
DPX502U  
DPX502UY  
INSTRUCTION MANUAL  
© B64-3829-00/00 (EW/E2W)  
 
Safety precautions  
Do Not Load 8 cm (3 in.) CDs in the CD slot  
If you try to load a 8 cm (3 in.) CD with its adapter into  
the unit, the adapter might separate from the CD and  
damage the unit.  
2WARNING  
To prevent injury or fire, take the following  
precautions:  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
About CD players/disc changers connected  
to this unit  
• Do not watch or fix your eyes on the unit’s display  
when you are driving for any extended period.  
• Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting  
and wiring work to professionals.  
Kenwood disc changers/ CD players released in 1998  
or later can be connected to this unit.  
Refer to the catalog or consult your Kenwood dealer  
for connectable models of disc changers/ CD players.  
Note that any Kenwood disc changers/ CD players  
released in 1997 or earlier and disc changers made by  
other makers cannot be connected to this unit.  
Connecting unsupported disc changers/CD players to  
this unit may result in damage.  
Set the "O-N" Switch to the "N" position for the  
applicable Kenwood disc changers/ CD players.  
The functions you can use and the information that  
can be displayed may differ depending on the models  
being connected.  
2CAUTION  
To prevent damage to the machine, take  
the following precautions:  
• Make sure to ground the unit to a negative 12V DC  
power supply.  
• Do not install the unit in a spot exposed to direct  
sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of  
water splashing.  
• When replacing a fuse, only use a new fuse with  
the prescribed rating. Using a fuse with the wrong  
rating may cause your unit to malfunction.  
• Use only the screws provided or specified for  
installation. If you use wrong screws, you could  
damage the unit.  
¤
You can damage both your unit and the CD changer if you  
connect them incorrectly.  
Lens Fogging  
When you turn on the car heater in cold weather,  
dew or condensation may form on the lens in the  
CD player of the unit. Called lens fogging, this  
condensation on the lens may not allow CDs to play.  
In such a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does not  
operate normally after a while, consult your Kenwood  
dealer.  
iPod is a trademark of Apple Inc., registered in  
the U.S. and other countries.  
The "AAC" logo is trademark of Dolby  
Laboratories.  
|
English  
3
 
Notes  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• When you purchase optional accessories, check with  
your Kenwood dealer to make sure that they work  
with your model and in your area.  
• The RDS feature won’t work where the service is not  
supported by any broadcasting station.  
• The characters which can be displayed by this unit  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off with  
a cloth moistened with neutral cleaner, then wipe it  
again with a clean soft dry cloth.  
¤
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth or  
using a volatile liquid such as thinner or alcohol may scratch  
the surface or erases characters.  
are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |  
~ .  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
Before using this unit for the first time  
This unit is initially set on the Demonstration mode.  
When using this unit for the first time, cancel the  
<Demonstration mode Setting> (page 31).  
About KENWOOD "Music Editor" of  
PC application attached to DPX502U/  
DPX502UY  
How to reset your unit  
• If the unit fails to operate properly, press the Reset  
button. The unit returns to factory settings when the  
Reset button is pressed.  
• "Music Editor" is recorded in the CD-ROM attached  
to this unit.  
• Remove the USB device before pressing the Reset  
button. Pressing the Reset button with the USB  
device installed can damage the data contained in  
the USB device. For how to remove the USB device,  
refer to <Playing USB (iPod) device> (page 19).  
• Press the reset button if the disc auto changer fails  
to operate correctly. Normal operation should be  
restored.  
• Refer to the attached installation manual for the  
installation method of "Music Editor".  
• Refer to the user’s manual recorded in the  
installation CD-ROM and Help of "Music Editor" for  
the operation method of "Music Editor".  
• The unit can play CD/ USB device created by "Music  
Editor".  
• Information about "Music Editor" upgrade is put on  
the site, www.kenwood.com.  
Reset button  
|
4
English  
 
About Audio file  
About USB device  
Playable Audio file  
• Install the USB device in the place where it will not  
prevent you from driving your vehicle properly.  
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma),  
WAV (.wav)  
• You cannot connect a USB device via a USB hub.  
Playable disc media  
CD-R/RW/ROM  
• Take backups of the audio files used with this unit.  
The files can be erased depending on the operating  
conditions of the USB device.  
We shall have no compensation for any damage  
arising out of erasure of the stored data.  
• No USB device comes with this unit. You need to  
purchase a commercially available USB device.  
• Do not directly connect the USB device to the USB  
connector on the panel. Connect it using a cable.  
Playable disc file format  
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.  
Playable USB device  
USB mass storage class, iPod with KCA-iP200  
Playable USB device file system  
FAT16, FAT32  
Although the audio files are complied with the  
standards listed above, the play maybe impossible  
depending on the types or conditions of media or  
device.  
• Leave the cap on when not using an USB device.  
• For how to play the audio files recorded in a USB  
device, see <CD/USB device/Audio file/External disc  
control features> (page 18).  
• When connecting the USB device, usage of the CA-  
U1EX (option) is recommended.  
Normal playback is not guaranteed when a cable  
other than the USB compatible cable is used.  
Connecting a cable whose total length is longer  
than 5 m can result in abnormal playback.  
Playing order of the Audio file  
In the example of folder/file tree shown below, the  
files are played in the order from to .  
<
v
:
:
Follder
Audiofile  
CD  
()  
vꢀ  
vꢆ  
vꢇ  
About DAB Tuner control  
Refer to A group on the Instruction manual of DAB  
Tuner KTC-9090DAB (optional accessory) for the  
control method of DAB Tuner function.  
However, the following control methods of the  
function for this unit may be differed from the  
Instruction manual; therefore, refer to the following  
supplemental instruction.  
vꢄ  
vꢉ  
v.  
An online manual about audio files is put on the  
site, www.kenwood.com/audiofile/. On this online  
manual, detailed information and notes which are not  
written in this manual are provided. Make sure to read  
through the online manual as well.  
<Auto Ensemble Memory Entry>  
1. Select the preset band for Auto Ensemble Memory  
Entry.  
2. Press the [AME] button for at least 2 seconds.  
Open Auto Ensemble Memory Entry.  
After storing in the memory finishes, the number  
of the pre-set buttons and the ensemble label are  
displayed.  
In this manual, the word "USB device" is used for flash  
memories and digital audio players which have USB  
terminals.  
<Searching by programme type and language>  
and <Languages to be displayed> in <Programme  
Type (PTY) Function>  
At the operation to press [DISP] button, use [TI]  
button instead.  
<Automatic Switching DAB priority>  
This function cannot be used.  
The word "iPod" appearing in this manual indicates the iPod  
connected with the KCA-iP200 (optional accessory). The  
iPod connected with the KCA-iP200 can be controlled from  
this unit. iPods that can be connected with the KCA-iP200  
are the iPod nano and the iPod with video. When an iPod  
is connected using a commercially available USB cable, it is  
handled as a mass-storage-class device.  
For the supported formats and types of USB device, refer to  
|
English  
5
 
Notes  
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
Handling CDs  
• Do not touch the recording surface of the CD.  
• Do not stick tape etc. on the CD, or use a CD with  
tape stuck on it.  
• Do not use disc type accessories.  
• Clean from the center of the disc and move  
outward.  
• When removing CDs from this unit, pull them out  
horizontally.  
• If the CD center hole or outside rim has burrs,  
use the CD only after removing the burrs with a  
ballpoint pen etc.  
Information on Disposal of Old Electrical  
and Electronic Equipment (applicable for  
EU countries that have adopted separate  
waste collection systems)  
Products with the symbol (crossed-out  
wheeled bin) cannot be disposed as  
household waste.  
Old electrical and electronic equipment  
should be recycled at a facility capable  
of handling these items and their waste  
byproducts. Contact your local authority  
for details in locating a recycle facility  
nearest to you. Proper recycling and waste  
disposal will help conserve resources whilst  
preventing detrimental effects on our  
health and the environment.  
CDs that cannot be used  
• CDs that are not round cannot be used.  
• CDs with coloring on the recording surface or CDs  
that are dirty cannot be used.  
• This unit can only play the CDs with  
The marking of products using lasers  
(Except for some areas)  
.
CLASS 1  
LASER PRODUCT  
This unit may not correctly play discs which do not  
have the mark.  
• You cannot play a CD-R or CD-RW that has not been  
finalized. (For the finalization process refer to your  
CD-R/CD-RW writing software, and your CD-R/CD-  
RW recorder instruction manual.)  
The label is attached to the chassis/case and says  
that the component uses laser beams that have been  
classified as Class 1. It means that the unit is utilizing  
laser beams that are of a weaker class. There is no  
danger of hazardous radiation outside the unit.  
|
6
English  
 
General features  
DISP  
Auxiliary input  
Control knob  
VOL  
ATT  
Q
SRC  
Clock display  
LOUD indicator  
ATT indicator  
* An equipment such as a portable audio player can  
be connected to the auxiliary input terminal using a  
commercially available mini-plug (3.5ø).  
Power  
Turning ON the Power  
Press the [SRC] button.  
This unit automatically turns full power OFF after 20  
minutes lapses in Standby mode in order to save the  
vehicle's battery.  
The time until full power OFF can be set in <Power OFF  
Timer> (page 30).  
When the power is ON, the <Security Code> (page 25) is  
displayed as "CODE ON" or "CODE OFF".  
Turning OFF the Power  
When connection of the iPod is recognized, the source  
display changes from "USB" to "iPod".  
USB (iPod) source is recognized as CD source on the  
connected unit.  
Use the mini-plug which is stereo type and does not  
have any resistance.  
Press the [SRC] button for at least 1 second.  
Selecting the Source  
Press the [SRC] button.  
Source required  
Display  
Tuner  
USB device (iPod)  
CD  
"TUNER"  
"USB" ("iPod")  
"CD"  
External disc (Optional accessory)  
Auxiliary input*  
"CD CH"  
"AUX"  
Auxiliary input (Optional accessory)  
Standby (Illumination only mode)  
"AUX EXT"  
"STANDBY"  
|
English  
7
 
General features  
Volume  
Audio Control  
Increasing Volume  
Turn the [VOL] knob clockwise.  
1 Select the source to adjust  
Press the [SRC] button.  
Decreasing Volume  
Turn the [VOL] knob counterclockwise.  
2 Enter Audio Control mode  
Press the [VOL] knob.  
3 Select the Basic Audio item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
Attenuator  
Turning the volume down quickly.  
Press the [ATT] button.  
Each time you press the button, the Attenuator  
turns ON and OFF.  
When the Attenuator is ON, the "ATT" indicator  
blinks.  
4 Adjust the Basic Audio item  
Turn the [VOL] knob.  
Adjustment Item Display  
Range  
Rear Volume  
Subwoofer level  
Bass level*  
Middle level*  
Treble level*  
Balance  
"R-VOL"  
"SW L"  
"BAS L"  
"MID L"  
"TRE L"  
"BAL"  
0 — 35  
–15 — +15  
–8 — +8  
–8 — +8  
–8 — +8  
System Q  
Left 15 — Right 15  
Rear 15 — Front 15  
Selecting the best sound setting preset for different  
types of music.  
Fader  
"FAD"  
Exit Audio Control mode (Volume control mode)  
1 Select the source to set  
* You can adjust these items in detail. Refer to <Adjusting  
the detail of Audio Control> (Page9).  
* Source tone memory: Puts the set up value in the  
memory per source. (Detail Audio item is included)  
Press the [SRC] button.  
2 Select the Sound type  
Press the [Q] button.  
5 Exit Audio Control mode  
Press any button.  
Press a button other than the [VOL] knob and [ATT]  
When you press the button once, the current  
sound setting is displayed.  
Each time you press the button, the sound setting  
alternates.  
button.  
Sound setting  
User memory  
Rock  
Pops  
Easy  
Display  
"USER"  
"ROCK"  
"POPS"  
"EASY"  
Top 40  
Jazz  
"TOP40"  
"JAZZ"  
Natural  
"NATURAL"  
User memory: The values set on the <Audio Control>  
(page 8).  
Change each setting value with the <Speaker Setting>  
(page 10).  
First, select the speaker type with the Speaker setting.  
|
8
English  
 
Adjusting the detail of Audio Control  
Among the Basic Audio items, you can adjust the Bass  
level, Middle level, and Treble level in detail.  
When you set the Bass Extend to ON, low frequency  
response is extended by 20%.  
You can exit the Audio Control mode at anytime by  
pressing any button except for [VOL] knob and [ATT]  
button.  
1 Select the Basic Audio item  
Select the desired item to be set in detail from  
followings;  
• Bass level  
• Middle level  
• Treble level  
For how to select Basic Audio items, see <Audio  
Control> (page 8).  
2 Enter Detail adjustment mode of Audio  
Control  
Press the [VOL] knob for at least 1 second.  
3 Select the Detail Audio item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
4 Adjust the Detail Audio item  
Turn the [VOL] knob.  
Bass level  
Adjustment Item  
Display  
Range  
Bass Center Frequency  
"BAS F"  
40/50/60/70/80/100/  
120/150 Hz  
Bass Q Factor  
Bass Extend  
"BAS Q"  
"B EX"  
1.00/1.25/1.50/2.00  
OFF/ON  
Middle level  
Adjustment Item  
Display  
Range  
Middle Center Frequency "MID F"  
0.5/1.0/1.5/2.0 kHz  
1.0/2.0  
Middle Q Factor  
"MID Q"  
Treble level  
Adjustment Item  
Display  
Range  
Treble Center Frequency "TRE"  
10.0/12.5/15.0/17.5 kHz  
5 Exit the Detail Audio Control mode  
Press the [VOL] knob for at least 1 second.  
|
English  
9
 
General features  
Audio Setup  
Speaker Setting  
Setting the Sound system, such as Cross over  
Network.  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type.  
1 Select the source to adjust  
1 Enter Standby  
Press the [SRC] button.  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Audio Setup mode  
Press the [VOL] knob for at least 1 second.  
2 Enter Speaker Setting mode  
Press the [VOL] knob.  
3 Select the Audio Setup item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
3 Select the Speaker type  
Turn the [VOL] knob.  
Each time you turn the knob, the setting alternates  
between the settings shown in the table below.  
4 Setup the Audio item  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Display  
Turn the [VOL] knob.  
"SP OFF"  
"SP 5/4"  
"SP 6*9/6"  
"SP OEM"  
Adjustment Item  
Display  
Range  
Through/40/60/80/100/120/  
150/180/220 Hz  
Front High Pass Filter "HPF"  
Rear High Pass Filter "HPR"  
Through/40/60/80/100/120/  
150/180/220 Hz  
50/60/80/100/120/Through Hz  
Reverse (180°)/ Normal (0°)  
–8 — 0 (AUX: -8— +8)  
OFF/ON  
4 Exit Speaker Setting mode  
Press the [VOL] knob.  
Low Pass Filter  
Subwoofer Phase  
Volume offset  
Loudness  
"LPF"  
"PHAS"  
"V-OFF"  
"LOUD"  
"2ZON"  
Subwoofer Output  
Turning the Subwoofer output ON or OFF.  
Dual Zone System  
OFF/ON  
Push the Control knob toward down for at least  
2 seconds.  
Each time you push the knob, Subwoofer output  
switches ON and OFF.  
When it is ON, "SW ON" is displayed.  
Volume offset: Sets each source’s volume as a difference  
from the basic volume.  
Loudness: Compensates for low and high tones  
during low volume. (Only the low tone is  
compensated for when the tuner is selected  
as a source.)  
Dual Zone System  
Main source and sub source (Auxiliary input) output  
Front channel and Rear channel separately.  
- Set up the channel of sub source by <Dual Zone  
System Setting> (page 27).  
- Select Main source by [SRC] button.  
- Adjust the volume of Front channel by [VOL] knob.  
- Adjust the volume of Rear channel by <Audio Control>  
(page 8).  
- The Audio Control has no effect on sub source.  
You can use the Dual Zone System with the internal  
auxiliary input.  
5 Exit Audio Setup mode  
Press the [VOL] knob for at least 1 second.  
|
10  
English  
 
TEL Mute  
The audio system automatically mutes when a call  
comes in.  
When a call comes in  
"CALL" is displayed.  
The audio system pauses.  
Listening to the audio during a call  
Press the [SRC] button.  
The "CALL" display disappears and the audio system  
comes back ON.  
When the call ends  
Hang up the phone.  
The "CALL" display disappears and the audio system  
comes back ON.  
To use the TEL Mute feature, you need to hook up  
the MUTE wire to your telephone using a commercial  
telephone accessory. Refer to <Connecting Wires to  
Terminals> (page 35).  
|
English  
11  
 
General features  
* When playing music from iPod or music edited by  
"Music Editor", the folder name display may show  
something different such as playlist or artist name  
depending on the music selection procedure.  
Switching Display  
Changing the information displayed.  
Press the [DISP] button.  
Each time the button is pressed the display  
switches as shown below.  
In Tuner source  
Information  
Display  
Program Service name or Frequency  
(FM)  
"FREQ/PS"  
Radio text, Program Service name or  
Frequency (FM)  
"R-TEXT"  
Frequency (MW, LW)  
Clock  
"FREQ"  
"CLOCK"  
In CD & External disc source  
Information  
Disc title  
Track title  
Track number & Play time  
Clock  
Display  
"D-TITLE"  
"T-TITLE"  
"P-TIME"  
"CLOCK"  
In Audio file source  
Information  
Display  
"TITLE"  
"ALBUM"  
"FOLDER"  
"FILE"  
Music title & Artist name  
Album name & Artist name  
Folder name*  
File name  
Play time & Music number  
Clock  
"P-TIME"  
"CLOCK"  
In Standby/ Auxiliary input source  
Information  
Source name  
Clock  
Display  
"SRC NAME"  
"CLOCK"  
When LX-AMP is connected, the item setup by the  
Display mode of LX-AMP is displayed.  
When the music number exceeds 1000, only the last 3  
digits of its number are displayed.  
When you select the clock display, the display setting of  
each source will be changed to the clock display.  
Music title, Artist name, and Album name cannot be  
displayed in WAV file.  
If the selected display item does not have any  
information, alternative information is displayed.  
|
12  
English  
 
Tuner features  
FM  
AM  
Control knob  
AME  
SRC  
1 - 6  
Frequency display  
Band display  
ST indicator  
Preset station number  
Tuning  
Selecting the station.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUNER" display.  
2 Select the band  
Push the Control knob towards [FM] or [AM].  
Each time you push the knob toward [FM], it  
switches between the FM1, FM2, and FM3 bands.  
3 Tune up or down band  
Push the Control knob towards [4] or [¢].  
During reception of stereo stations the "ST" indicator is  
ON.  
|
English  
13  
 
Tuner features  
Function of remote control  
Auto Memory Entry  
Putting stations with good reception in the memory  
automatically.  
Direct Access Tuning  
Entering the frequency and tuning.  
1 Select the band for Auto Memory Entry  
1 Select the band  
Push the Control knob towards [FM] or [AM].  
Press the [FM] or [AM] button.  
2 Open Auto Memory Entry  
2 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote  
control.  
Press the [AME] button for at least 2 seconds.  
"A-MEMORY" is displayed.  
When 6 stations that can be received are put in the  
memory Auto Memory Entry closes.  
"– – – –" is displayed.  
3 Enter the frequency  
Press the number buttons on the remote  
When the <AF (Alternative Frequency)> (page 28) is ON,  
only RDS stations are put in the memory.  
When Auto Memory Entry is done in the FM2 band, the  
RDS stations preset in the FM1 band are not put in the  
memory.  
control.  
Example:  
Desired frequency  
92.1 MHz (FM)  
810 kHz (AM)  
Press button  
[0], [9], [2], [1]  
[0], [8], [1], [0]  
Likewise, when Auto Memory Entry is done in the FM3  
band, RDS stations preset in FM1 or FM2 are not put in  
the memory.  
Cancelling Direct Access Tuning  
Press the [DIRECT] button on the remote  
control.  
Preset Tuning  
Recalling the stations in the memory.  
You can enter the FM band frequency in steps of a  
minimum of 0.1 MHz.  
1 Select the band  
Push the Control knob towards [FM] or [AM].  
Station Preset Memory  
Putting a station in the memory.  
2 Recall the station  
Press the desired [1] — [6] button.  
1 Select the band  
Push the Control knob towards [FM] or [AM].  
2 Select the frequency to put in the memory  
Push the Control knob towards [4] or [¢].  
3 Put the frequency in the memory  
Press the desired [1] — [6] button for at least 2  
seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the memory  
on each [1] — [6] button.  
|
14  
English  
 
RDS features  
Control knob  
TI  
SRC  
1 - 6  
Radio text  
TI indicator  
PTY indicator  
RDS indicator  
Receiving other traffic information stations  
Push the Control knob towards [4] or [¢].  
Traffic Information  
Changing to traffic information automatically when  
a traffic bulletin starts even when you are not  
listening to the radio.  
Traffic information can be switched when it is on the  
Tuner Source. However, you cannot switch the Traffic  
information during reception of the Traffic bulletin  
switched from the source other than the Tuner.  
Press the [TI] button.  
Each time you press the button, the Traffic  
information function turns ON and OFF.  
When traffic information is ON, "TI" indicator is ON.  
When a traffic information station is not being  
received the "TI" indicator blinks.  
Radio Text Scroll  
Scrolling the displayed radio text.  
When a traffic bulletin starts, "TRAFFIC" is displayed  
and the audio changes to traffic information.  
Push the Control knob toward up for at least 2  
seconds.  
During reception of an AM station when the Traffic  
Information function is turned ON, the frequency  
changes to an FM station.  
When the <Display Illumination Control> (page 26) is set  
to OFF, the display may black out while scrolling.  
During reception of traffic information the adjusted  
volume is automatically remembered, and the next time  
the audio changes to traffic information, the volume  
automatically becomes the remembered volume.  
|
English  
15  
 
RDS features  
PTY (Program Type)  
Selecting the Program Type and searching for a  
station.  
Speech and Music include the Program type shown  
below.  
Music: No.12 — 17, 26 — 30  
Speech: No.3 — 11, 18 — 25, 31  
1 Enter PTY mode  
You can put the Program Type in the [1] — [6] button  
memory and for quick recall. Refer to the <Program Type  
preset> (page 16).  
You can change the display language. Refer to  
<Changing Language for PTY Function> (page 17).  
Press the Control knob.  
During PTY mode the "PTY" indicator is ON.  
This function cannot be used during a traffic bulletin or  
AM reception.  
3 Search for the selected Program Type station  
Push the Control knob towards [4] or [¢].  
When you want to search for other stations, push  
[4] or [¢] of the Control knob again.  
2 Select the Program Type  
Push the Control knob towards up or down.  
Each time you push the knob, the Program Type  
alternates between program types shown in the  
table below.  
When the selected Program Type is not found, "NO PTY"  
is displayed. Select another Program Type.  
No.  
1.  
Program Type  
Speech  
Display  
"SPEECH"  
"MUSIC"  
4 Exit PTY mode  
2.  
Music  
Press the Control knob.  
3.  
News  
"NEWS"  
4.  
5.  
6.  
Current Affairs  
Information  
Sport  
"AFFAIRS"  
"INFO"  
"SPORT"  
Program Type preset  
Putting the Program Type in the Preset button  
memory and quick recall.  
7.  
8.  
9.  
Education  
Drama  
Culture  
Science  
Varied  
Pop Music  
Rock Music  
Easy Listening Music  
Light Classical  
Serious Classical  
Other Music  
Weather  
"EDUCATE"  
"DRAMA"  
"CULTURE"  
"SCIENCE"  
"VARIED"  
"POP M"  
"ROCK M"  
"EASY M"  
"LIGHT M"  
"CLASSICS"  
"OTHER M"  
"WEATHER"  
"FINANCE"  
"CHILDREN"  
"SOCIAL"  
"RELIGION"  
"PHONE IN"  
"TRAVEL"  
"LEISURE"  
"JAZZ"  
"COUNTRY"  
"NATION M"  
"OLDIES"  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
18.  
19.  
20.  
21.  
22.  
23.  
24.  
25.  
26.  
27.  
28.  
29.  
30.  
31.  
Presetting the Program Type  
1 Select the Program Type to preset  
Refer to <PTY (Program Type)> (page 16).  
2 Preset the Program Type  
Press the desired [1] — [6] button for at least 2  
seconds.  
Recalling the preset Program Type  
Finance  
1 Enter PTY mode  
Children’s programs  
Social Affairs  
Religion  
Phone In  
Travel  
Refer to <PTY (Program Type)> (page 16).  
2 Recall the Program Type  
Press the desired [1] — [6] button.  
Leisure  
Jazz Music  
Country Music  
National Music  
Oldies Music  
Folk Music  
Documentary  
"FOLK M"  
"DOCUMENT"  
|
16  
English  
 
Changing Language for PTY Function  
Selecting the Program Type display language.  
1 Enter PTY mode  
Refer to <PTY (Program Type)> (page 16).  
2 Enter Changing Language mode  
Press the [TI] button.  
3 Select the language  
Push the Control knob towards up or down.  
Each time you push the knob, the language  
alternates between the languages shown in the  
table below.  
Language  
English  
French  
Swedish  
German  
Display  
"ENGLISH"  
"FRENCH"  
"SWEDISH"  
"GERMAN"  
4 Exit Changing Language mode  
Press the [TI] button.  
|
English  
17  
 
CD/USB device/Audio file/External disc control features  
Control knob  
USB connector  
SRC  
S.MODE SCAN RDM/3/ REP F.SEL M.RDM  
A.RDM  
Track number  
Play time  
IN indicator  
Disc number  
Playing CD & Audio file  
USB Device Connection  
1 Remove the cap and connect the  
When a disc is inserted  
Press the [SRC] button.  
Select the "CD" display.  
USB cable.  
2 Connect the USB device to the unit  
using the USB cable.  
When a CD is inserted, the "IN" indicator is ON.  
Pause and play  
Press the Control knob.  
Each time you press the knob, the audio pauses or  
plays.  
Eject the CD  
Press the [0] button.  
For the audio files and discs you can play with this unit,  
refer to <About Audio file> (page 5).  
You can play the file made by KENWOOD Music Editor by  
the same operation.  
You can eject the disc for 10 minutes after switching off  
the engine.  
When connecting the USB device, usage of the CA-U1EX  
(option) is recommended.  
|
18  
English  
 
Playing USB (iPod) device  
Drive Search  
Selecting the device inserted in the Multi Card  
Reader.  
When the USB device is not connected  
Connect the USB device  
Playback of the file contained in the USB device  
starts.  
1 Put the playback to pause  
Press the [S.MODE] button.  
2 Select a device  
When the USB device is connected  
Push the Control knob towards up or down.  
Select USB source  
Press the [SRC] button.  
Select the "USB" (or "iPod") display.  
3 Restart playback  
Press the [S.MODE] button.  
This unit is compliant with Multi Card Readers with a  
maximum of 4 slots.  
For the audio files that can be played with this unit and  
the devices that can be connected to this unit, refer to  
<About Audio file> (page 5).  
If a device is inserted during connection of the Multi  
Card Reader, it is not recognized. Select the Remove  
mode with reference to <Playing USB (iPod) device>  
(page 19), remove the Card Reader, and then insert the  
memory.  
The word "iPod" appearing in this manual indicates the  
iPod connected with the KCA-iP200 (optional accessory).  
Refer to <About Audio file> (page 5).  
If you start playback after connecting the iPod, the music  
that has been played by the iPod is played first.  
In this case, "RESUMING" is displayed without displaying  
a folder name, etc. Changing the browse item will  
display a correct title, etc.  
When the iPod is connected to this unit, "KENWOOD" or  
"" is displayed on the iPod to indicate that you cannot  
operate the iPod.  
When the USB device is connected to this unit, it can be  
charged up provided that this unit is powered.  
When the Multi Card Reader is used, refer to <Drive  
Search> (page 19).  
After you stopped playing a file contained in the USB  
device, you can restart playing the file from the point  
where you stopped its playback.  
Even after removing the USB device, you can restart  
playing the file from the point where you stopped its  
playback as long as the files contained in the USB device  
are all the same.  
Be sure to insert the USB device connector as far as it will  
go.  
You can play the file made by KENWOOD Music Editor by  
the same operation.  
Pause and play  
Press the Control knob.  
Each time you press the knob, the audio pauses or  
plays.  
Removing the USB device  
1 Set the remove mode as the USB source  
Press the [0] button for at least 2 seconds.  
"REMOVE" display blinks.  
2 Remove the USB device.  
|
English  
19  
 
CD/USB device/Audio file/External disc control features  
Function of disc changer/ Audio file  
Playing External Disc  
Playing discs set in the optional accessory disc  
Disc Search/Folder/Album Search  
player connected to this unit.  
Switching between folders/albums contained in  
the disc in the disc changer, media, or device being  
played now.  
Press the [SRC] button.  
Select the display for the disc player you want.  
Display examples:  
Push the Control knob towards up or down.  
Display  
"CD CH"  
"MD CH"  
Disc player  
CD changer  
MD changer  
Function of remote control  
Direct Music Search  
Pause and play  
Press the Control knob.  
Doing Music Search by entering the music number.  
Each time you press the knob, the audio pauses or  
plays.  
1 Enter the music number  
Press the number buttons on the remote  
control.  
Disc 10 is displayed as "0".  
The functions that can be used and the information that  
can be displayed will differ depending on the external  
disc players being connected.  
You can select Direct music Search up to 999.  
2 Do music Search  
Press the [4] or [¢] button.  
Cancelling Direct Music Search  
Press the [38] button.  
Fast Forwarding and Reversing  
Fast Forwarding  
Hold down toward [¢] with the Control knob.  
Release to resume the playback.  
This function is not available on iPod and the music  
edited by "Music Editor".  
Reversing  
Hold down toward [4] with the Control knob.  
Function of disc changers with remote control  
Release to resume the playback.  
Direct Disc Search  
Doing Disc Search by entering the disc number.  
There is no sound while the Audio file is being searched.  
The accurate play time is not displayed during fast  
forwarding or reversing of the Audio file.  
1 Enter the disc number  
Press the number buttons on the remote  
control.  
2 Do Disc Search  
Music Search  
Press the [+] or [] button.  
Switching between music contained in the disc or  
folder being played now.  
Cancelling Direct Disc Search  
Press the [38] button.  
Push the Control knob towards [4] or [¢].  
Input "0" to select disc 10.  
|
20  
English  
 
Track/File/Disc/Folder Repeat  
Random Play  
Replaying the music, disc in the Disc changer or  
Audio file folder you are listening to.  
Play all the music on the disc or Audio file folder in  
random order.  
Press the [REP] button.  
Press the [RDM] button.  
Each time you press the button, the Repeat Play  
alternates between the modes shown in the tables  
below.  
Each time you press the button, Random Play turns  
ON or OFF.  
When the Random mode is ON, "DISC RDM"/"FOLD  
RDM"/"RDM ON" is displayed.  
In CD & External disc source  
Repeat play  
Track Repeat  
Disc Repeat (In Disc Changer)  
OFF  
Display  
When you push the Control knob toward [¢], the next  
"TRAC REP"  
"DISC REP"  
"REP OFF"  
selected music starts.  
In Audio file source  
Function of disc changer  
Magazine Random Play  
Play the music on all the discs in the disc changer in  
random order.  
Repeat play  
File Repeat  
Folder Repeat*  
OFF  
Display  
"FILE REP"  
"FOLD REP"  
"REP OFF"  
Press the [M.RDM] button.  
Each time you press the button, the Magazine  
Random Play turns ON or OFF.  
* This function is not available on iPod and the music  
When the Magazine Random mode is ON, "MGZN  
RDM" is displayed.  
edited by "Music Editor".  
When you push the Control knob toward [¢], the next  
Scan Play  
Playing the first part of each music on the disc or  
Audio file folder you are listening to and searching  
for the music you want to hear.  
selected music starts.  
1 Start Scan Play  
Press the [SCAN] button.  
"TRAC SCN"/"FILE SCN"/"SCAN ON" is displayed.  
2 Release it when the music you want to listen  
to is played  
Press the [SCAN] button.  
This function is not available on iPod and the music  
edited by "Music Editor".  
|
English  
21  
 
CD/USB device/Audio file/External disc control features  
Function of Audio file  
Function of non-iPod and non-"Music Editor" file  
All Random Play  
File Select 1 mode  
Playing randomly from all of the Audio files  
recorded in the media.  
Select the target folder by tracing the hierarchical  
levels of folders. This is convenient when managing  
audio files by folder.  
Press the [A.RDM] button for at least 1 second.  
When the random mode is ON, "ALL RDM" is  
displayed.  
1 Enter File Select 1 mode  
Press the [F.SEL] button.  
Select the "F-SEL1" display.  
Folder name display  
Cancelling the All Random Play  
Press the [A.RDM] button.  
Displays the current folder name.  
When you push the Control knob toward [¢], the next  
selected music starts.  
This function is not available on iPod and the music  
edited by "Music Editor".  
2 Select the folder  
Operation type  
Operation  
Function of iPod, "Music Editor" file  
Movement between folders Push the Control knob towards right or left.  
Selection of folder Push the Control knob towards up.  
Return to previous folder Push the Control knob towards down.  
Return to root folder Press the [3] button.  
File select  
Selecting the music you want to listen to from the  
device or media being played now.  
1 Enter File Select mode  
Press the [F.SEL] button.  
Select the "F-SEL" display.  
Select the folder containing the music you want to  
listen to.  
3 Determine the folder  
2 Search for a music  
Press the Control knob.  
Select the category item using the Control  
knob.  
The music in the determined folder are displayed.  
4 Select the music you want to listen to  
Operation type  
Operation  
Operation type  
Operation  
Movement between Push the Control knob towards right or left.  
items  
Movement between music Push the Control knob towards right or left.  
Return to folder selection Press the Control knob for at least 1 second.  
step  
Selection of item  
Return to previous item Push the Control knob for at least 1 second.  
Return to first item Press the [3] button.  
Press the Control knob.  
Return to root folder  
Press the [3] button.  
5 Play the selected music  
Names of all the music are displayed in "SONGS" in  
the audio file.  
Press the Control knob.  
Selecting a music will play it from the beginning.  
Scrolling the file/folder name display  
Push the Control knob toward up for at least 2  
seconds.  
Cancelling File Select  
Press the [F.SEL] button.  
Cancelling File Select 1  
Press the [F.SEL] button twice.  
|
22  
English  
 
Function of non-iPod and non-"Music Editor" file  
Text/Title Scroll  
Scrolling the displayed CD text, Audio file text, or  
MD title.  
File Select 2 mode  
Select the target folder within the folders  
containing audio files. The folder which contains  
playable audio files is only displayed.  
Push the Control knob toward up for at least 2  
seconds.  
1 Enter File Select 2 mode  
Press the [F.SEL] button twice.  
Select the "F-SEL2" display.  
Folder name display  
When the <Display Illumination Control> (page 26) is set  
to OFF, the display may black out while scrolling.  
Displays the current folder name.  
2 Select the folder  
Push the Control knob towards right or left.  
Each time you push the knob, the folders  
containing audio files are displayed one after  
another.  
Check the name of upper level folder  
Push the Control knob towards up.  
Each time you push the knob towards up, the  
folder just above the current folder is displayed.  
Each time you push the knob towards down, the  
folder just below the current folder is displayed.  
"
" is displayed while the upper level folder is  
displayed.  
3 Determine the folder  
Press the Control knob.  
The music in the determined folder are displayed.  
4 Select the music you want to listen to  
Operation type  
Operation  
Movement between music Push the Control knob towards right or left.  
Return to folder selection Press the Control knob for at least 1 second.  
step  
5 Play the selected music  
Press the Control knob.  
Scrolling the file/folder name display  
Push the Control knob toward up for at least 2  
seconds.  
Cancelling File Select 2  
Press the [F.SEL] button.  
|
English  
23  
 
Menu system  
Control knob  
SRC  
MENU  
Menu display  
NEWS indicator  
RDS indicator  
Menu System  
Setting beep sound during operation, etc.  
functions.  
The Menu system basic operation method is  
explained here. The reference for the Menu items  
and their setting content is after this operation  
explanation.  
4 Exit Menu mode  
Press the [MENU] button.  
When other items those applicable to the basic  
operation method above are displayed, their setting  
content chart is entered. (Normally the setting listed at  
the top of the chart is the original setting.)  
Also, the explanation for items that are not applicable  
(<Manual Clock Adjustment> etc.) are entered step by  
step.  
1 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
2 Select the menu item  
Push the Control knob towards up or down.  
Example: When you want to set the beep sound  
select the "BEEP" display.  
3 Set the menu item  
Push the Control knob towards right or left.  
Example: When you select "BEEP", each time you  
push the knob it alternates between  
"BEEP ON" or "BEEP OFF". Select 1 of them  
as the setting.  
You can continue by returning to step 2 and  
setting other items.  
|
24  
English  
 
In Standby mode  
Resetting the Security Code function when the  
audio unit is first used after removed from the  
battery power source or the Reset button is  
pressed  
Security Code  
Activating the Security Code disables the usage  
of audio unit by someone else. Once the Security  
Code is activated, the entry of authorized Security  
Code is required to turn on the audio unit when it is  
removed from the vehicle. Indication of this Security  
Code activation prevents your precious audio unit  
from stealing.  
1 Turn the power ON.  
2 Do the step 4 through 7 step operation, and  
reenter the security code.  
"APPROVED" is displayed.  
Now, you can use the unit.  
If an incorrect code is entered, "WAITING" is displayed,  
and the input prohibition periods shown in the table  
below is generated.  
When you activate the Security Code function, it cannot be  
released.  
Note, your Security Code is the 4 digit number entered in  
your "Car Audio Passport" in this package.  
After the input prohibition time lapses, "CODE" is  
displayed, and you can reenter the code.  
1 Enter Standby  
Number of times the  
incorrect code was input  
1
2
3
4
Input prohibited time  
Press the [SRC] button.  
Select the "STANDBY" display.  
5 minutes  
1 hour  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
When "MENU" is displayed, "CODE SET" is also  
displayed.  
24 hours  
3 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When "ENTER" is displayed, "CODE" is also  
displayed.  
In Standby mode  
Touch Sensor Tone  
Setting the operation check sound (beep sound)  
ON/OFF.  
4 Select the digits to enter  
Push the Control knob towards right or left.  
5 Select the Security Code numbers  
Display  
"BEEP ON"  
"BEEP OFF"  
Setting  
Beep is heard.  
Beep canceled.  
Push the Control knob towards up or down.  
6 Repeat step 4 and 5, and complete the Security  
Code.  
7 Confirm the Security Code  
Press the Control knob for at least 3 seconds.  
When "RE-ENTER" is displayed, "CODE" is also  
displayed.  
8 Do the step 4 through 7 step operation, and  
reenter the security code.  
"APPROVED" is displayed.  
The Security Code function activates.  
If you enter a Code different from your Security Code,  
you have to start over from step 4.  
9 Exit Security Code mode  
Press the [MENU] button.  
|
English  
25  
 
Menu system  
In Standby mode  
Display Illumination Control  
This function turns off the display when you  
perform no operation for 5 seconds. This function is  
effective when you are driving at night.  
Manual Clock Adjustment  
You can do this adjustment when the <Synchronize Clock>  
(page 26) is set as OFF.  
Display  
Setting  
1 Select Clock Adjustment mode  
Push the Control knob towards up or down.  
Select the "CLK ADJ" display.  
"DISP ON"  
Keeps the display on.  
Turns off the display when you perform no  
operation for 5 seconds.  
"DISP OFF"  
2 Enter Clock Adjust mode  
Press the Control knob for at least 1 second.  
The clock display blinks.  
Set the Display Illumination Control when the  
<Demonstration mode Setting> (page 31) is set to OFF.  
When the display is off, pressing any key will turn on the  
display.  
When the display is off, you cannot perform any  
operation except for the following:  
3 Adjust the hours  
Push the Control knob towards up or down.  
Adjust the minutes  
Push the Control knob towards right or left.  
Volume  
Attenuator  
Selecting the source  
Ejecting the disc  
Turning off the power  
USB remove mode  
4 Exit Clock adjustment mode  
Press the [MENU] button.  
During function control, such as the Menu System, the  
display stays on.  
In Standby mode  
Synchronize Clock  
Synchronizing the RDS station time data and this  
unit’s clock.  
In Standby mode  
Dimmer  
Display  
"SYNC ON"  
"SYNC OFF"  
Setting  
Synchronizes the time.  
Adjust the time manually.  
Dimming this unit’s display automatically when the  
vehicle light switch is turned ON.  
Display  
"DIM AUTO"  
"DIM OFF"  
Setting  
The display dims.  
The display doesn’t dim.  
It takes 3 to 4 minutes to synchronize the clock.  
In Standby mode  
Switching preout  
Alternating the preout between the rear and  
subwoofer. (With the subwoofer the sound outputs  
without being effected by fader control.)  
Display  
Setting  
"SWPRE R"  
"SWPRE SW"  
Rear preout.  
Subwoofer preout.  
|
26  
English  
 
In Standby mode  
When LX AMP unit connecting  
Built-in Amp Setting  
AMP Control  
Controlling the built-in amplifier.  
Turning OFF this control enhances the preout  
quality.  
You can control the LX AMP connected to the unit.  
1 Select AMP Control mode  
Push the Control knob towards up or down.  
Select the "AMP CTRL" display.  
Display  
Setting  
"AMP ON"  
"AMP OFF"  
The built-in amplifier activates.  
The built-in amplifier deactivates.  
2 Enter AMP Control mode  
Press the Control knob for at least 1 second.  
3 Select the AMP Control item for adjustment  
Push the Control knob towards up or down.  
Other than Standby mode/  
When the Dual Zone System is ON  
For the details on the AMP Control item, see the  
Instruction manual attached to the LX AMP.  
Dual Zone System Setting  
Setting the Front channel and Rear channel sound  
in the Dual Zone System.  
4 Adjust the AMP Control item  
Push the Control knob towards right or left.  
Display  
"ZONE2 R"  
Setting  
5 Exit AMP Control mode  
Sub source (Auxiliary input source) is to be rear  
channel.  
Sub source (Auxiliary input source) is to be front  
channel.  
Press the [MENU] button.  
"ZONE2 F"  
You cannot use the LX AMP operation during standby  
mode.  
In Audio file source  
Supreme Setting  
When AAC, MP3 or WMA files encoded at a low bit  
rate (less than 96kbps (fs=44.1k, 48kHz)) are played,  
this function restores their high frequency region  
to approach the sound quality of equivalents of  
these files encoded at a high bit rate. Processing is  
optimized for the compression format used (AAC,  
MP3, or WMA), and adjustment is made for the bit  
rate used.  
Display  
Setting  
"SPRM ON"  
Plays sound using the Supreme function.  
"SPRM OFF"  
Plays the original sound stored in the audio file.  
The sound effect may be imperceptible depending  
on the relationship between the audio file format and  
setting.  
This function is not available on the iPod.  
|
English  
27  
 
Menu system  
Other than Standby mode  
In Tuner mode  
News Bulletin with Timeout Setting  
Tuning Mode  
The tuner automatically changes when a news  
bulletin starts even if the radio is not being listened  
to. Also, you can set the time interval when  
interruption is prohibited.  
Sets the tuning mode.  
Tuning mode  
Auto seek  
Display  
"AUTO 1"  
Operation  
Automatic search for a station.  
Search in order of the stations in  
the Preset memory.  
Preset station seek "AUTO 2"  
Display and Setting  
"NEWS OFF"  
Manual  
"MANUAL" Normal manual tuning control.  
"NEWS 00M"  
"NEWS 90M"  
AF (Alternative Frequency)  
When you set "NEWS 00M" — "NEWS 90M", the  
News Bulletin Interrupt function is ON.  
When the News Bulletin is ON, the "NEWS"  
indicator is ON.  
When the news bulletin starts, "NEWS" is displayed,  
and the tuner changes to the news bulletin.  
When the reception is poor, automatically alternate  
to another frequency broadcasting the same  
program in the same RDS network with better  
reception.  
Display  
"AF ON"  
"AF OFF"  
Setting  
The AF function is ON.  
The AF function is OFF.  
If you choose the "20M" setting, further news bulletins  
will not be received for 20 minutes once the first news  
bulletin is received.  
When the AF function is ON, the "RDS" indicator  
is ON.  
The news bulletin volume is the same level that was set  
for <Traffic Information> (page 15).  
This news bulletin function is only available if the desired  
station sends PTY-code for news bulletin or belongs to  
<Enhanced Other Network>-Network sending PTY-code  
for news bulletin.  
When no other stations with stronger reception are  
available for the same program in the RDS network, you  
may hear the incoming broadcast in bits and snatches.  
Turn OFF the AF function in such a case.  
When the News Bulletin Interrupt function is ON, the  
tuner changes to an FM station.  
Restricting RDS Region (Region  
Restrict Function)  
You can choose whether or not to restrict the  
RDS channels, received with the AF function for a  
particular network, to a specific region.  
In Tuner mode  
Local Seek  
Only stations whose reception is good are searched  
in auto seek tuning.  
Display  
Setting  
Display  
Setting  
"LO.S OFF"  
"LO.S ON"  
The local seek function is OFF.  
The local seek function is ON.  
"REG ON"  
"REG OFF"  
The Region Restrict Function is ON.  
The Region Restrict Function is OFF.  
If AF function is not restricted to the specified region and  
network, the AF function sets up to search the station  
with good reception in the same RDS network.  
|
28  
English  
 
• "GAME"  
• "VIDEO"  
• "TV"  
Auto TP Seek  
When the TI function is ON and the reception is  
poor while listening to a traffic information station,  
another traffic information station with better  
reception will be searched for automatically.  
6 Exit Auxiliary input display setting mode  
Press the [MENU] button.  
Display  
"ATPS ON"  
"ATPS OFF"  
Setting  
The Auto TP Seek Function is ON.  
The Auto TP Seek Function is OFF.  
When operation stops for 10 seconds, the name at that  
time is registered, and the Auxiliary input display setting  
mode closes.  
You can only set the Auxiliary input display when the  
built-in auxiliary input or the auxiliary input of optional  
KCA-S220A is used.  
In FM reception  
Monaural Reception  
You can reduce the noise when stereo broadcasts  
are received as monaural.  
Function of DPX502UY  
In Standby mode  
Selecting Russian Characters  
Display  
Setting  
"MONO OFF"  
"MONO ON"  
The monaural reception is OFF.  
The monaural reception is ON.  
Setting up the display of Russian characters and  
undistinguishable English characters.  
Display  
Setting  
"RUS ON"  
"RUS OFF"  
Displays texts using Russian characters.  
Displays texts using European characters.  
Auxiliary Input Display Setting  
Selecting the display when changing to Auxiliary  
input source.  
Texts displayed using Russian characters are as follows.  
- Folder name/ File name/ Music title/ Artist name/  
Album name  
- CD text (internal CD source)  
Texts cannot distinguish upper case and lower case in  
Russian characters.  
1 Select Auxiliary input source  
Press the [SRC] button.  
Select the "AUX"/"AUX EXT" display.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
3 Select Auxiliary input display setting mode  
Push the Control knob towards up or down.  
Select the "NAME SET" display.  
4 Enter Auxiliary input display setting mode  
Press the Control knob for at least 1 second.  
The presently selected Auxiliary input display is  
displayed.  
5 Select the Auxiliary input display  
Push the Control knob towards right or left.  
Each time you push the knob, the display alternates  
as listed below.  
• "AUX"/"AUX EXT"  
• "DVD"  
• "PORTABLE"  
|
English  
29  
 
Menu system  
In Standby mode  
Text Scroll  
Setting the displayed text scroll.  
CD Read Setting  
When there is a problem with playing a CD with  
special format, this setting plays the CD by force.  
Display  
"SCL MANU"  
"SCL AUTO"  
Setting  
Doesn’t scroll.  
Scrolls when the display changes.  
Display  
Setting  
"CD READ1"  
"CD READ2"  
Play CD and Audio file.  
Play CD by force.  
The text scrolled is listed below.  
- CD text  
- Folder name/ File name/ Music title/ Artist name/  
Album name  
- MD title  
Some music CDs may not play even in the "CD READ2"  
mode.  
- Radio text  
Other than Standby mode  
Audio Preset Memory  
In Standby mode  
Registering the value setup by Sound Control. The  
memory cannot be erased by the Reset button.  
Built-in Auxiliary input Setting  
Set the Built-in Auxiliary Input function.  
1 Setup Sound Control  
Refer to the following operations to setup the  
Sound Control.  
Display  
"AUX OFF" When selecting the source there’s no Auxiliary Input.  
"AUX ON" When selecting the source there’s Auxiliary Input.  
Setting  
- <Audio Control> (page 8)  
- <Audio Setup> (page 10)  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
In Standby mode  
Power OFF Timer  
3 Select Audio Preset mode  
Setting the timer to turn this unit’s power OFF  
automatically when Standby mode continues.  
Using this setting can save the vehicle’s battery  
power.  
Push the Control knob towards up or down.  
Select the "A-PRESET" display.  
4 Enter Audio Preset mode  
Press the Control knob for at least 1 second.  
Display  
Setting  
5 Select the Audio Preset Memory  
Push the Control knob towards up or down.  
Select the "MEMORY" display.  
"OFF – – –"  
Power OFF Timer function is OFF.  
"OFF 20M"  
(Original setting)  
Turns the power OFF after 20 minutes.  
"OFF 40M"  
"OFF 60M"  
Turns the power OFF after 40 minutes.  
Turns the power OFF after 60 minutes.  
6 Put the Audio Preset in the memory  
Press the Control knob for at least 2 seconds.  
The "MEMORY" display blinks 1 time.  
7 Exit Audio Preset mode  
Press the [MENU] button.  
Register 1 pair of Audio Preset Memory. You cannot  
register by the source.  
When you press the Reset, all the sources will be the  
setting value which is registered.  
|
30  
English  
 
The following items cannot be registered.  
Volume, Balance, Fader, Loudness, Volume offset, Dual  
Zone System, Rear Volume  
In Standby mode  
Firmware version display  
Displaying the firmware version with the unit.  
1 Select the firmware version display mode  
Push the Control knob towards up or down.  
Select the "F/W VER" display.  
Other than Standby mode  
Audio Preset Recall  
Recalling the sound setup registered by <Audio  
Preset Memory> (page 30).  
2 Display the firmware version  
Push the Control knob towards right or left.  
1 Select the source  
Press the [SRC] button.  
In Standby mode  
2 Enter Menu mode  
Demonstration mode Setting  
Sets the demonstration mode.  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
3 Select Audio Preset mode  
1 Select the Demonstration mode  
Push the Control knob towards up or down.  
Select the "DEMO" display.  
Push the Control knob towards up or down.  
Select the "A-PRESET" display.  
4 Enter Audio Preset mode  
2 Set the Demonstration mode  
Press the Control knob for at least 1 second.  
Press the Control knob for at least 2 seconds.  
Each time you press the knob at least 2 seconds,  
the Demonstration mode alternates between the  
settings shown in the table below.  
5 Select the Audio Preset Recall  
Push the Control knob towards up or down.  
Select the "RECALL" display.  
Display  
"DEMO ON"  
"DEMO OFF"  
Setting  
6 Recall the Audio Preset  
The Demonstration mode function is ON.  
Exit Demonstration mode (Normal mode).  
Press the Control knob for at least 2 seconds.  
The "RECALL" display blinks 1 time.  
7 Exit Audio Preset mode  
Press the [MENU] button.  
The User memory of <System Q> (page 8) is changed to  
the value which was recalled.  
The source tone memory item of <Audio Control> (page  
8) is changed to the value which was recalled by the  
selected source.  
|
English  
31  
 
Basic Operations of remote control  
SRC  
ATT  
VOL  
SRC  
AT T  
VOL  
AUD  
AUD  
FM/AM/+/–  
2-ZONE  
DIRECT  
[0] — [9]  
: This button is used when Kenwood Bluetooth  
HANDS FREE BOX is connected. For more  
information, refer to the instruction manual of  
Bluetooth HANDS FREE BOX.  
Loading and Replacing the battery  
Basic operations  
Use two "AA"/ "R6"-size batteries.  
Slide the cover while pressing downwards to  
remove it as illustrated.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
[VOL] buttons  
Adjusts the volume.  
[SRC] button  
Each time you press the button, the source  
alternates.  
For the source alternating order refer to <Selecting  
the Source> (page 7).  
[ATT] button  
Turns the volume down quickly.  
When the button is pressed again, the volume  
returns to the previous level.  
2WARNING  
Store unused batteries out of the reach of children.  
Contact a doctor immediately if the battery is  
accidentally swallowed.  
¤
Do not set the remote control in hot places such as on  
the dashboard.  
|
32  
English  
 
Audio Control  
In Disc/USB source  
[AUD] button  
Selects the Audio item to be adjusted.  
[4]/ [¢] buttons  
Going forwards and backwards between music.  
[VOL] buttons  
Adjusts the Audio item.  
[+]/ [] buttons  
Going forwards and backwards between disc/  
folders.  
Refer to <Audio Control> (page 8) for the operation  
method, such as the procedures for Audio control and  
others operations.  
[38] button  
Each time you press the button, the music is played  
or paused.  
The remote control can only select and adjust the Basic  
Audio item. Selecting and adjusting of the Detail Audio  
item cannot be done.  
[0] — [9] buttons  
When in <Direct Music Search> (page 20) and  
<Direct Disc Search> (page 20), enters the music/  
disc number.  
Dual Zone System  
[2-ZONE] button  
Each time you press the button, "2ZON" of <Audio  
Setup> (page 10) is turned ON or OFF.  
[5]/ [] buttons  
Adjusts the volume of the rear channel.  
The rear channel activates while the Dual Zone  
System is ON.  
In Tuner source  
[FM]/ [AM] buttons  
Selects the band.  
Each time you press the [FM] button, the band  
alternates between the FM1, FM2, and FM3 bands.  
[4]/ [¢] buttons  
Tune up or down band.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset stations.  
[DIRECT] button  
Enters and cancels the <Direct Access Tuning>  
(page 14) mode.  
[38] button  
Enters and cancels the <PTY (Program Type)>  
(page 16) mode.  
|
English  
33  
 
Accessories/ Installation Procedure  
Accessories  
¤
If the power is not turned ON ("PROTECT" is displayed),  
the speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
If your car is not prepared for this special connection-  
system, consult your Kenwood dealer.  
Use a commercially available conversion connector if the  
connector does not fit in the vehicle connector.  
Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not  
be linked with the ignition (i.e., it will not turn on and off  
along with the ignition). If you want to link the unit’s power  
with the ignition, connect the ignition wire to a power  
source that can be turned on and off with the ignition key.  
If the fuse blows, first make sure that the wires have not  
caused a short circuit, then replace the old fuse with one  
with the same rating.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent short circuits, also do not remove  
the caps on the ends of the unconnected wires or the  
terminals.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may receive damage or fail  
to work if you share the - wires and/or ground them to  
any metal part in the car.  
1
..........1  
2
..........2  
3
..........1  
Installation Procedure  
1. To prevent short circuits, remove the key from the  
ignition and disconnect the - terminal of the  
battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the wire on the wiring harness.  
4. Take Connector B on the wiring harness and  
connect it to the speaker connector in your vehicle.  
5. Take Connector A on the wiring harness and  
connect it to the external power connector on your  
vehicle.  
6. Connect the wiring harness connector to the unit.  
7. Install the unit in your car.  
After the unit is installed, check whether the brake lamps,  
indicators, wipers, etc. on the car are working properly.  
If the console has a lid, make sure to install the unit so  
that the faceplate does not hit the lid when closing and  
opening.  
Mount the unit so that the mounting angle is 30° or less.  
8. Reconnect the - terminal of the battery.  
9. Press the reset button.  
If You Want to Connect iPod  
iPod  
AUDIO OUT  
KCA-iP200 (Optional accessory)  
No other optional accessory can be connected because  
the USB connector and the AUX input are used for iPod  
connection.  
Dual Zone System in <Audio Setup> (page 10) will become  
unavailable.  
|
34  
English  
 
Connecting Wires to Terminals  
REMO.CONT  
Steering remote control (Light Blue/Yellow)  
To Kenwood disc changer/  
External optional accessory  
To connect these leads, refer to the relevant  
instruction manuals.  
FM/AM antenna input (JASO)  
Antenna Cord  
Fuse (10A)  
Front left output (White)  
Front right output (Red)  
Rear left output /Sub Woofer left output (White)  
Rear right output /Sub Woofer right output (Red)  
Wiring harness  
(Accessory1)  
TEL mute wire (Brown)  
Connect to the terminal that is grounded when  
either the telephone rings or during conversation.  
MUTE  
To connect the Kenwood navigation system, consult  
your navigation manual.  
If no connections are made, do not  
let the wire come out from the tab.  
Power control/Motor antenna  
control wire (Blue/White)  
Connect either to the power control terminal  
when using the optional power amplifier, or to the  
antenna control terminal in the vehicle.  
P. C O N T  
ANT.CONT  
Battery wire (Yellow)  
Ignition wire (Red)  
See next page  
A–7 Pin (Red)  
A–4 Pin (Yellow)  
Connector A  
Connector B  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
|
English  
35  
 
Connecting Wires to Terminals  
Connector Function Guide  
2WARNING  
Pin Numbers for Cable Colour  
Functions  
Connecting the ISO Connector  
ISO Connectors  
External Power  
Connector  
The pin arrangement for the ISO connectors depends on  
the type of vehicle you drive. Make sure to make the proper  
connections to prevent damage to the unit.  
A-4  
A-5  
A-6  
A-7  
A-8  
Yellow  
Battery  
Power Control  
Dimmer  
Ignition (ACC)  
Earth (Ground)  
Connection  
The default connection for the wiring harness is described in  
1 below. If the ISO connector pins are set as described in 2  
or 3, make the connection as illustrated.  
Please be sure to reconnect the cable as shown 2 below to  
install this unit to the Volkswagen vehicles etc.  
Blue/White  
Orange/White  
Red  
Black  
Speaker  
Connector  
1(Default setting) The A-7 pin (red) of the vehicle’s  
ISO connector is linked with the ignition, and the A-  
4 pin (yellow) is connected to the constant power  
supply.  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
B-1  
B-2  
B-3  
B-4  
B-5  
B-6  
B-7  
B-8  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right (–)  
Front Right (+)  
Front Right (–)  
Front Left (+)  
Front Left (–)  
Rear Left (+)  
Rear Left (–)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
Green/Black  
2The A-7 pin (red) of the vehicle’s ISO connector is  
connected to the constant power supply, and the  
A-4 pin (yellow) is linked to the ignition.  
A-7 Pin (Red)  
Ignition cable (Red)  
Unit  
Vehicle  
A-4 Pin (Yellow)  
Battery cable (Yellow)  
3The A-4 pin (yellow) of the vehicle’s ISO connector  
is not connected to anything, while the A-7 pin  
(red) is connected to the constant power supply  
(or both the A-7 (red) and A-4 (yellow) pins are  
connected to the constant power supply).  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
When the connection is made as in 3 above, the unit’s  
power will not be linked to the ignition key. For that reason,  
always make sure to turn off the unit’s power when the  
ignition is turned off.  
To link the unit’s power to the ignition, connect the ignition  
cable (ACC...red) to a power source that can be turned on  
and off with the ignition key.  
|
36  
English  
 
Installation  
Installing the Unit  
Firewall or metal support  
Screw (M4X8)  
(commercially available)  
Bend the tabs of the mounting  
sleeve with a screwdriver or similar  
utensil and attach it in place.  
Self-tapping screw  
(commercially available)  
Accessory3  
Metal mounting strap  
(commercially available)  
|
English  
37  
 
Removing the Unit  
Removing the Hard Rubber Frame  
(escutcheon)  
1 Engage the catch pins on the removal tool 2 and  
remove the two locks on the lower level.  
Lower the frame and pull it forward as shown in  
the figure.  
Lock  
Catch  
Accessory2  
2 When the lower level is removed, remove the  
upper two locations.  
The frame can be removed from the top side in the same  
manner.  
Removing the Unit  
1 Refer to the section <Removing the Hard Rubber  
Frame> and then remove the hard rubber frame.  
Accessory2  
2 Remove the Hex-head screw with integral washer  
(M4X8) on the back panel.  
3 Insert the two removal tools 2 deeply into the  
slots on each side, as shown.  
4 Lower the removal tool towards the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
5 Pull the unit all the way out with your hands,  
carefully not to drop it.  
|
38  
English  
 
Troubleshooting Guide  
Some functions of this unit may be disabled by  
some settings made on this unit.  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
!
!
Cannot switch to Aux source.  
• AUX is not turned on. <Built-in Auxiliary input  
Setting> (page 30)  
• AUX cannot be used when the KCA-iP200 is  
connected.  
General  
? The Touch Sensor Tone doesn’t sound.  
The preout jack is being used.  
The Touch Sensor Tone can’t be output from the  
preout jack.  
• Cannot set up the subwoofer.  
• Cannot set up subwoofer phase.  
• No output from the subwoofer.  
• Cannot set up the low pass filter.  
• Preout is not set to subwoofer. <Switching  
preout> (page 26)  
Tuner source  
? Radio reception is poor.  
The car antenna is not extended.  
• <Subwoofer Output> (page 10) is not set to On.  
• The Dual zone function is enabled. <Audio  
Setup> (page 10)  
Pull the antenna out all the way.  
The antenna control wire is not connected.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>  
(page 35).  
!
• Cannot set up the high pass filter.  
• Cannot set up the Fader.  
The Dual zone function is enabled. <Audio  
Setup> (page 10)  
Disc source  
? The specified disc does not play, but another one  
plays instead.  
!
!
Cannot set up the subwoofer phase.  
Low pass filter is set to Through. <Audio Setup>  
(page 10)  
The specified CD is quite dirty.  
Clean the CD.  
The disc is loaded in a different slot from that  
specified.  
• Cannot select the output destination of the  
subsource in the Dual zone.  
• Cannot adjust the volume of the rear speakers.  
The Dual zone function is disabled. <Audio  
Setup> (page 10)  
Eject the disc magazine and check the number  
for the specified disc.  
The disc is severely scratched.  
Try another disc instead.  
Audio file source  
!
!
No Audio control effect on AUX.  
The Dual zone function is enabled. <Audio  
Setup> (page 10)  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
• Cannot register a security code.  
• Cannot set up Display Illumination Control.  
<Demonstration mode Setting> (page 31) is not  
turned off.  
Clean the media, referring to the CD cleaning of  
the section on <Handling CDs> (page 6).  
The audio file is broken or not supported.  
Damaged and unsupported files are skipped.  
The recording condition is bad.  
Record the media again or use another media.  
!
!
Cannot play audio files.  
<CD Read Setting> (page 30) is set to "2".  
USB device source  
Cannot File select.  
The Random play function is enabled.  
? The USB device is not detected.  
The USB connector is disconnected.  
Connect the connector of the USB device  
properly.  
? The USB device does not play its audio files.  
The USB connector is disconnected.  
Connect the connector of the USB device  
properly.  
|
English  
39  
 
Troubleshooting Guide  
IN (Blink):  
PROTECT:  
NA FILE:  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
The messages shown below display your  
systems condition.  
EJECT:  
• No disc magazine has been loaded in  
the changer. The disc magazine is not  
completely loaded.  
• No CD in the unit.  
The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and then  
the protection function is activated.  
Wire or insulate the speaker cable  
properly and press the reset button. If  
the "PROTECT" code does not disappear,  
consult your nearest service center.  
NO DISC:  
TOC ERR:  
No disc has been loaded in the disc  
magazine.  
• No disc has been loaded in the disc  
magazine.  
• The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
READ ERR:  
• The number of files or folders which are  
stored in the connected USB device is above  
the limitation.  
An Audio file is played with a format that this  
unit can’t support.  
----  
• The file system of the connected USB device  
is broken.  
Copy the files and folders for the USB  
kenwood.com/usb/. If the error message is  
still displayed, initialize the USB device or  
use other USB devices.  
COPY PRO:  
DEMO:  
A copy-protected file is played.  
----  
The Demonstration mode has been selected.  
The <Demonstration mode Setting> (page  
31) is ON. Turn it OFF.  
NO DVICE:  
NA DVICE:  
The USB device is selected as a source  
although no USB device is connected.  
Change the source to any source other  
than USB. Connect an USB device, and  
change the source to USB again.  
E-05:  
The disc is unreadable.  
BLANK:  
NO TRACK:  
Nothing has been recorded on the MD.  
No tracks are recorded on the MD, although it  
has a title.  
An unsupported USB device is connected.  
For the supported USB devices, refer to  
<http://www.kenwood.com/usb/>.  
NO PANEL:  
E-77:  
The faceplate of the slave unit being  
connected to this unit has been removed.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
"E-77" code does not disappear, consult  
your nearest service center.  
NO MUSIC/E-15:• The connected USB device contains no  
playable audio file.  
• Media was played that doesn’t have data  
recorded that the unit can play.  
E-99:  
Something is wrong with the disc magazine.  
Or the unit is malfunctioning for some reason.  
Check the disc magazine. And then press  
the reset button on the unit. If the "E-99"  
code does not disappear, consult your  
nearest service center.  
USB ERR:  
The connected USB device is rated a current  
capacity higher than the allowable limit.  
Check the USB device with reference to  
<http://www.kenwood.com/usb/>.  
Some trouble may have occurred to the  
connected USB device.  
Change the source to any source other  
than USB. Remove the USB device.  
LOAD:  
Discs are being exchanged in the Disc  
changer.  
iPod ERR:  
REMOVE:  
Connection to the iPod has failed.  
Remove the USB device and then  
reconnect it.  
Confirm that the software for the iPod is  
the latest version.  
READING:  
HOLD:  
The unit is reading the data on the disc.  
The protective circuit in the unit activates  
when the temperature inside the automatic  
disc changer exceeds 60°C (140°F), stopping  
all operation.  
Cool down the unit by opening the  
windows or turning on the air conditioner.  
As the temperature falls below 60°C  
(140°F), the disc will start playing again.  
The Remove mode has been selected for the  
USB device. You can remove the USB device  
safely.  
|
40  
English  
 
Specifications  
Specifications subject to change without notice.  
WAV signal  
FM tuner section  
Frequency range (50 kHz space)  
: 87.5 MHz – 108.0 MHz  
Usable sensitivity (S/N = 26dB)  
: 0.7 μV /75 Ω  
Quieting Sensitivity (S/N = 46dB)  
: 1.6 μV /75 Ω  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 65 dB  
Selectivity (DIN)( 400 kHz)  
: ≥ 80 dB  
Stereo separation (1 kHz)  
: 35 dB  
: Linear-PCM  
Audio section  
Maximum output power  
: 50 W x 4  
Output power (DIN 45324, +B=14.4V)  
: 30 W x 4  
Speaker impedance  
: 4 - 8 Ω  
Tone action  
Bass : 100 Hz 8 dB  
Middle : 1 kHz 8 dB  
Treble : 10 kHz 8 dB  
Preout level / Load (during disc play)  
: 2500 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
MW tuner section  
Frequency range (9 kHz space)  
: 531 kHz – 1611 kHz  
Usable sensitivity (S/N = 20dB)  
: 25 μV  
USB Interface  
USB Standard  
: USB1.1/ 2.0  
File System  
LW tuner section  
Frequency range  
: 153 kHz – 281 kHz  
Usable sensitivity (S/N = 20dB)  
: 45 μV  
: FAT16/ 32  
Maximum Supply current  
: 500 mA  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
CD player section  
AAC decode  
Laser diode  
: AAC-LC ".m4a" files  
: GaAlAs  
WAV signal  
: Linear-PCM  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 1 Bit  
Auxiliary input  
Frequency response ( 1 dB)  
: 20 Hz – 20 kHz  
Input Maximum Voltage  
: 1200 mV  
Input Impedance  
: 100 kΩ  
Spindle speed  
: 1000 – 400 rpm (CLV 2times)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
: 0.008 %  
Signal to Noise ratio (1 kHz)  
: 105 dB  
Dynamic range  
: 93 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
General  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 112 x 160 mm  
Weight  
: 1.60 kg  
AAC decode  
: AAC-LC ".m4a" files  
|
English  
41  
 
 
 
 

John Lewis Range JLRC101 User Manual
JVC Headphones HANC120 User Manual
JVC Speaker CS AW6040 User Manual
Kambrook Fan KFA413 User Manual
Karcher Pressure Washer G 4000 RH User Manual
Karcher Pressure Washer K 2425 User Manual
Kenmore Iron 62984 User Manual
Kenmore Range 7903105 User Manual
Kettler Baby Swing 08371 190 User Manual
KitchenAid Dishwasher KUDI01DL User Manual