Kenwood Car Stereo System KDC W5041U User Manual

CD-RECEIVER  
KDC-W5641U  
KDC-W5541U  
KDC-W5141U  
KDC-W5041U  
KDC-W4141  
KDC-W4041  
INSTRUCTION MANUAL  
© B64-3958-00/00 (EW/E2W)  
Before use  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• When you purchase optional accessories, check with  
your Kenwood dealer to make sure that they work  
with your model and in your area.  
• The characters which can be displayed by this unit  
are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |  
~ .  
2WARNING  
To prevent injury or fire, take the following  
precautions:  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
Before using this unit for the first time  
This unit is initially set on the Demonstration mode.  
When using this unit for the first time, cancel the  
<Demonstration mode Setting> (page 13).  
• The RDS feature won’t work where the service is not  
supported by any broadcasting station.  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
How to reset your unit  
• If this unit or the connected unit (disc auto changer,  
etc.) fails to operate properly, press the Reset button.  
The unit returns to factory settings when the Reset  
button is pressed.  
Handling CDs  
• Do not touch the recording surface of the CD.  
• Do not stick tape etc. on the CD, or use a CD with  
tape stuck on it.  
Reset button  
• Do not use disc type accessories.  
• Clean from the center of the disc and move  
outward.  
• When removing CDs from this unit, pull them out  
horizontally.  
• If the CD center hole or outside rim has burrs,  
use the CD only after removing the burrs with a  
ballpoint pen etc.  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off with  
a cloth moistened with neutral cleaner, then wipe it  
again with a clean soft dry cloth.  
¤
CDs that cannot be used  
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth or  
using a volatile liquid such as thinner or alcohol may scratch  
the surface or erases characters.  
• CDs that are not round cannot be used.  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get dirty, wipe  
them with a clean soft dry cloth.  
• CDs with coloring on the recording surface or CDs  
that are dirty cannot be used.  
• This unit can only play the CDs with  
Lens Fogging  
.
This unit may not correctly play discs which do not  
have the mark.  
• You cannot play a CD-R or CD-RW that has not been  
finalized. (For the finalization process refer to your  
CD-R/CD-RW writing software, and your CD-R/CD-  
RW recorder instruction manual.)  
When you turn on the car heater in cold weather,  
dew or condensation may form on the lens in the  
CD player of the unit. Called lens fogging, this  
condensation on the lens may not allow CDs to play.  
In such a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does not  
operate normally after a while, consult your Kenwood  
dealer.  
English  
|
3
Basic Operation  
Display  
D
Display Disc slot  
Auxiliary input  
[TI]  
[M.JOG]  
Release  
[ ]  
ꢀꢁ  
[1] [2] [3] [4] [5] [6]  
[SRC]  
Control knob  
USB Terminal  
[
]
damaged by shocks or jolts.  
General functions  
Keep the faceplate in its faceplate case while detached.  
Do not place the faceplate (and the faceplate case) in areas  
exposed to direct sunlight, excessive heat or humidity. Also  
avoid places with too much dust or the possibility of water  
splashing.  
Power/Source select button  
Turns on the power.  
[SRC]  
When the power is on, the source switches between  
Tuner (“TUNER”) , USB or iPod (“USB” or “iPod”),  
CD (“CD”) , Auxiliary input (“AUX”), and Standby  
(“STANDBY”) each time this button is pressed.  
Press at least 1 second to turn off the power.  
To prevent deterioration, do not touch the terminals of the  
unit or faceplate with your fingers.  
Auxiliary input  
Auxiliary input  
Used to connect a portable audio device with mini-  
plug cable (3.5 ø).  
When the power is ON, the <Security Code> (page 12) is  
displayed as "CODE ON" or "CODE OFF".  
Use the mini-plug cable (stereo) which does not have any  
resistance.  
For whether USB devices and iPod can be connected, refer  
to <About Audio file> (page 15).  
When an optional accessory is connected, the source name  
for each device appears.  
This unit automatically turns full power OFF after 20  
minutes lapses in Standby mode in order to save the  
vehicle's battery. The time until full power OFF can be set in  
“POWER OFF” of <Menu System> (page 11).  
When connection of the iPod is recognized, the source  
display changes from "USB" to "iPod".  
Muting volume upon reception of phone call  
When there is a call, “CALLis displayed and the audio  
system is paused.  
When the call ends, “CALLdisappears and the audio  
system comes back on.  
The audio system comes back on when [SRC] is  
pressed during a call.  
Volume control  
Turn the knob to adjust the volume.  
Control knob  
Subwoofer output  
Control knob  
Switches between ON (“SUBWOOFER ON”) and OFF  
(“SUBWOOFER OFF”) each time pushing toward down  
for at least 2 seconds.  
Faceplate release  
Release  
Releases the faceplate lock so that it can be removed.  
Refer to the following diagram when reattaching the  
faceplate.  
Text/Title scroll  
Control knob  
Scrolls the CD, audio file, and Radio text display when  
pushing toward up for at least 2 seconds.  
Tuner functions  
Band select  
Control knob  
Switches between FM1, FM2, and FM3 each time  
pushing toward up.  
¤
Switches to AM when pushing toward down.  
The faceplate is a precision piece of equipment and can be  
|
4
KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
: Indicates the button etc. to operate.  
Tuning  
Control knob  
Pause and play  
[38]  
Switches between pause and play each time this  
button is pressed.  
Changes the frequency when pushing toward left or  
right.  
Disc ejection  
[0]  
During reception of stereo stations the “ST” indicator is ON.  
You can eject the disc for 10 minutes after switching off the  
Traffic information  
[TI]  
engine.  
Turns ON or OFF the Traffic Information function.  
When the function is turned ON, “TI” indicator is ON.  
If traffic bulletin starts when the function is ON,  
“TRAFFIC INFO” is displayed and traffic information is  
received.  
USB device removing  
[0]  
Press this button for 2 seconds or longer to select  
the remove mode, and the remove the USB device.  
During the remove mode, “USB REMOVE” is displayed.  
Music search  
Control knob  
If the volume is adjusted during reception of traffic  
information, the adjusted volume is memorized  
automatically. The memorized volume will be applied next  
time the Traffic Information function is turned ON.  
Changes the music when pushing toward left or right.  
Fast reverses or forwards the music while keeping  
pushing toward left or right. (No sound is output  
while playing audio file.)  
Preset memory  
Memorizes the station selected when pressing for at  
least 2 seconds.  
[1] - [6]  
Folder search  
Control knob  
Changes the folder containing the audio file when  
pushing toward up or down.  
Auto memory entry  
Memorizes six stations with good reception  
[TI]  
Select mode  
[M.JOG]  
automatically when pressed for at least 2 seconds.  
After pressing this button, you can quickly search  
songs with the control knob. See <List Select> (page  
10), <iPod Select> (page 10) for details.  
Preset tuning  
[1] - [6]  
Recalls the memorized station.  
Track/ File/ Folder repeat play  
[4]  
Disc & Audio file play functions  
Switches between Track Repeat (“TRAC REP ON”) and  
OFF (“REP OFF”) when pressed while playing a CD.  
Switches between File Repeat (“FILE REP ON”), Folder  
Repeat (“FOLD REP ON”), and OFF (“REP OFF”) when  
pressed while playing an audio file.  
Disc play  
Disc slot  
Starts playing when a disc is inserted.  
When a CD is inserted, the “IN” indicator is ON.  
3 inch (8 cm) CD cannot be used. Attempt to insert using  
an adapter can cause malfunction.  
The folder repeat operation cannot be performed while  
iPod is playing.  
USB device play (KDC-W5641U/W5541U/W5141U/  
W5041U) USB Terminal  
Used to connect the USB device to the USB cable  
(optional accessory) which is connected to the USB  
terminal.  
Scan play  
[2]  
Successively plays the intro of the music in the disc or  
folder.  
When Scan Play is turned on, “TRAC SCAN ON”/ “FILE  
SCAN ON” is displayed.  
When the USB device is connected, the “USB”  
indicator is ON.  
The Scan paly operation cannot be performed while iPod is  
playing.  
For the playable audio file, media, and devices, refer to  
<About Audio file> (page 15).  
Random play  
[3]  
Randomly plays the music in the disc or folder.  
When Random Play is turned on, “DISC RDM ON”/  
“FOLD RDM ON” is displayed.  
English  
|
5
General Operation  
Audio Control  
Audio Setup  
You can adjust following Audio Control items;  
You can set Sound system , such as follows;  
Adjustment Item Display  
Range  
0 — 35  
–15 — +15  
“L1”/”L2”/“OFF”(The  
indicator turns on according to  
the setting.)  
Adjustment Item  
Front High Pass Filter* “HPF F”  
Display  
Range  
Through/80/100/120/ 150/180  
Hz  
Through/80/100/120/ 150/180  
Hz  
60*1/80/120/160*2/Through Hz  
Rear volume*  
Subwoofer level  
Bass Boost**  
“R-VOLUME”  
“SUB-W L”  
“B.BOOST-L”  
Rear High Pass Filter* “HPF R”  
Low Pass Filter  
Subwoofer Phase*  
Volume offset  
Loudness*  
Dual Zone System*  
“LPF SW”  
“PHASE”  
Reverse (180°)/ Normal (0°)  
System Q  
“NATURAL/  
Natural/User setting/Rock/  
“V-OFFSET” –8 — 0 (AUX: -8— +8)  
“LOUDNESS” OFF/ON  
“2ZONE”  
“USER”/“ROCK”/ Pops/Easy/Top 40/Jazz  
“POPS”/“EASY”/ (The indicator turns on  
“TOP40”/“JAZZ” according to the setting.)  
OFF/ON  
Bass level  
Middle level  
Treble level  
Balance  
“BASS L”  
“MID L”  
“TRE L”  
“BALANCE”  
“FADER”  
–8 — +8  
–8 — +8  
–8 — +8  
Left 15 — Right 15  
Rear 15 — Front 15  
*Function of KDC-W5641U/W5541U/W5141U/W5041U.  
*1KDC-W5641U/W5541U/W5141U/W5041U only.  
*2KDC-W4141/W4041 only.  
Fader  
Volume offset: Sets each source’s volume as a difference  
from the basic volume.  
Exit Audio Control mode (Volume control mode)  
Loudness: Compensates for low and high tones during  
low volume. (Only the low tone is compensated for  
when the tuner is selected as a source.)  
Dual Zone System  
Main source and sub source (Auxiliary input) output  
Front channel and Rear channel separately.  
- Set up the channel of sub source by “ZONE2” of <Menu  
System> (page 11).  
*Function of KDC-W5641U/W5541U/W5141U/W5041U.  
**Function of KDC-W4141/W4041.  
“USER”: The customized Bass, Middle, and Treble levels  
are effective. On the KDC-W5641U/W5541U/W5141U/  
W5041U, this item can be selected at any time. On the  
KDC-W4141/W4041, this item is displayed only when  
the tone quality has been adjusted. On the KDC-W4141/  
W4041, this item disappears when another setting is  
selected.  
- Select Main source by [SRC] button.  
- Adjust the volume of Front channel by Control knob.  
- Adjust the volume of Rear channel by <Audio Control>  
(page 6).  
You can set Bass, Middle, and Treble for each source.  
- The Audio Control has no effect on sub source.  
1 Select the source to adjust  
Press the [SRC] button.  
1 Select the source to adjust  
Press the [SRC] button.  
2 Enter Audio Control mode  
Press the Control knob.  
2 Enter Audio Setup mode  
Press the Control knob for at least 1 second.  
3 Select the Audio item to adjust  
Press the Control knob.  
3 Select the Audio Setup item to adjust  
Press the Control knob.  
4 Adjust the Audio item  
Turn the Control knob.  
4 Adjust the Audio setup item  
Turn the Control knob.  
5 Exit Audio Control mode  
Press any button.  
Press a button other than the Control knob or 0  
button.  
5 Exit Audio Setup mode  
Press the Control knob for at least 1 second.  
|
6
KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Speaker Setting  
Display Switching  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type as follows;  
Changes displayed information on each source  
following;  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Display  
In Tuner source  
“SP SEL OFF”  
“SP SEL 5/4”  
“SP SEL 6*9/6”  
“SP SEL OEM”  
Information  
Display  
Program Service name or Frequency  
Radio text, Program Service name or Frequency  
Clock  
“FREQUENCY/PS”  
“RADIO TEXT”  
“CLOCK”  
1 Enter Standby  
In CD & External disc source  
Press the [SRC] button.  
Information  
Disc title  
Track title (In External disc source)  
Play time & Track number  
Clock  
Display  
Select the “STANDBY” display.  
“DISC TITLE”  
“TRACK TITLE”  
“P-TIME”  
2 Enter Speaker Setting mode  
Press the Control knob.  
“CLOCK”  
3 Select the Speaker type  
Turn the Control knob.  
In Audio file source  
4 Exit Speaker Setting mode  
Information  
Display  
Press the Control knob.  
Music title & Artist name  
Album name & Artist name  
Folder name  
File name  
Play time & Music number  
Clock  
“TITLE/ARTIST”  
“ALBUM/ARTIST”  
“FOLDER NAME”  
“FILE NAME”  
“P-TIME”  
“CLOCK”  
In Standby/ Auxiliary input source  
Information  
Source name  
Clock  
Display  
“SOURCE NAME”  
“CLOCK”  
1 Enter Switching Display mode  
Press the [38] button for at least 1 second.  
“DISPLAY SELis displayed.  
2 Select the Display item  
Push the Control knob towards right or left.  
3 Exit Switching Display mode  
Press the [38] button.  
When you select the clock display, the display setting of  
each source will be changed to the clock display.  
If the selected display item does not have any  
information, alternative information is displayed.  
When selecting "FOLDER NAME" while playing with  
iPod, names will be displayed depending on currently  
selected browsing items.  
English  
|
7
Tuner Operation  
is displayed. Select another Program Type.  
PTY (Program Type)  
Selecting the Program Type below and searching  
for a station;  
4 Exit PTY mode  
Press the [38] button.  
No.  
Program Type  
Display  
1.  
Speech  
“SPEECH”  
“MUSIC”  
2.  
Music  
Program Type preset  
Putting the Program Type in the Preset button  
memory and quick recall.  
3.  
News  
“NEWS”  
4.  
Current Affairs  
Information  
Sport  
“AFFAIRS”  
“INFO”  
“SPORT”  
5.  
6.  
Presetting the Program Type  
7.  
Education  
Drama  
“EDUCATE”  
“DRAMA”  
“CULTURE”  
“SCIENCE”  
“VARIED”  
“POP M”  
“ROCK M”  
“EASY M”  
“LIGHT M”  
“CLASSICS”  
“OTHER M”  
“WEATHER”  
“FINANCE”  
“CHILDREN”  
“SOCIAL”  
“RELIGION”  
“PHONE IN”  
“TRAVEL”  
“LEISURE”  
“JAZZ”  
“COUNTRY”  
“NATION M”  
“OLDIES”  
“FOLK M”  
“DOCUMENT”  
8.  
1 Select the Program Type to preset  
9.  
Culture  
Refer to <PTY (Program Type)>.  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
18.  
19.  
20.  
21.  
22.  
23.  
24.  
25.  
26.  
27.  
28.  
29.  
30.  
31.  
Science  
Varied  
2 Preset the Program Type  
Press the desired [1] — [6] button for at least 2  
seconds.  
Pop Music  
Rock Music  
Easy Listening Music  
Light Classical  
Serious Classical  
Other Music  
Weather  
Recalling the preset Program Type  
1 Enter PTY mode  
Refer to <PTY (Program Type)>.  
Finance  
Children’s programs  
Social Affairs  
Religion  
2 Recall the Program Type  
Press the desired [1] — [6] button.  
Phone In  
Travel  
Leisure  
Changing Language for PTY Function  
Selecting the Program Type display language as  
follows;  
Jazz Music  
Country Music  
National Music  
Oldies Music  
Folk Music  
Documentary  
Language  
English  
French  
Display  
"ENGLISH"  
"FRENCH"  
"GERMAN"  
German  
Speech and Music include the Program type shown  
below.  
1 Enter PTY mode  
Music: No.12 — 17, 26 — 30  
Speech: No.3 — 11, 18 — 25, 31  
Refer to <PTY (Program Type)>.  
1 Enter PTY mode  
2 Enter Changing Language mode  
Press the [38] button.  
Press the [TI] button.  
During PTY mode the “PTY” indicator is ON.  
3 Select the language  
Push the Control knob towards up or down.  
This function cannot be used during a traffic bulletin or  
AM reception.  
4 Exit Changing Language mode  
Press the [TI] button.  
2 Select the Program Type  
Push the Control knob towards up or down.  
3 Search for the selected Program Type station  
Push the Control knob towards right or left.  
When the selected Program Type is not found, “NO PTY”  
|
8
KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Music disc/Audio file Operation  
Function of remote control  
Play Functions of Disc Changer  
While a disc in the disc changer is being played, the  
following play functions can be used.  
Direct Access Tuning  
Entering the frequency and tuning.  
Playing the Current Song or Disc Repeatedly.  
(Repeat play)  
Press the [4] button.  
1 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote  
control.  
Pressing the button repeatedly selects Track Repeat  
play on (“TRAC REP ON”), Disc Repeat play on  
(“DISC REP ON”), and Repeat play off (“REP OFF”)  
sequentially.  
"– – – –" is displayed.  
2 Enter the frequency  
Press the number buttons on the remote  
control.  
Randomly plays the music in the disc changer.  
(Magazine random play)  
Press the [6] button.  
Pressing the button toggles the setting between  
Magazine random play on (“MGZN RDM ON”) and  
off (“RDM OFF”).  
Example:  
Desired frequency  
92.1 MHz (FM)  
Press button  
[0], [9], [2], [1]  
[0], [8], [1], [0]  
810 kHz (AM)  
Cancelling Direct Access Tuning  
Press the [DIRECT] button on the remote  
control.  
Function of remote control  
Direct Music Search  
Searchs the music by entering the track number.  
You can enter the FM band frequency in steps of a  
minimum of 0.1 MHz.  
1 Enter the music number  
Press the number buttons on the remote  
control.  
2 Search the music  
Press the [4] or [¢] button.  
Cancelling Direct Music Search  
Press the [38] button.  
Direct Music Search cannot be performed during playing  
of iPod, Random play, or scan play.  
English  
|
9
Music disc/Audio file Operation  
Function of disc changers with remote control  
Function of KDC-W5641U/KDC-W5541U  
Function of iPod  
Direct Disc Search  
Searchs the disc by entering the disc number.  
iPod Select  
Search for the song you want to listen to by  
selecting the same menu item as that of iPod.  
1 Enter the disc number  
Press the number buttons on the remote  
control.  
1 Enter Multi Jog Select mode  
Press the [M.JOG] button.  
“MULTI JOG ON” is displayed.  
Displays the play list.  
2 Search the disc  
Press the [FM] or [AM] button.  
Cancelling Direct Disc Search  
Press the [38] button.  
2 Searching for and playing a song  
Operation type  
Operation  
Movement between items Turn the Control knob.  
Input “0” to select disc 10.  
Direct Disc Search cannot be performed during playing  
of Random play or scan play.  
Selection of item  
Press the Control knob.  
Return to previous item  
Return to Top menu  
Push the Control knob towards up.  
Push the Control knob towards up for at  
least 2 seconds.  
Cancelling the Multi Jog Select mode  
Press the [M.JOG] button.  
Function of USB/CD of Audio file  
List Select  
Search for the song you want to listen to by tracing  
the media file structure.  
iPod Select cannot be performed during Random play.  
1 Enter Multi Jog Select mode  
Press the [M.JOG] button.  
Function of Music CD  
“MULTI JOG ON” is displayed.  
Displays the current Audio file name.  
Track Select  
Select the song you want to listen to by turning the  
control knob.  
2 Searching for and playing a song  
Operation type  
Movement between  
folders/files  
Operation  
1 Enter Multi Jog Select mode  
Press the [M.JOG] button.  
“MULTI JOG ON” is displayed.  
Displays the current music No.  
Turn the Control knob.  
Selection of folder/flie  
Press the Control knob.  
Return to previous folder Push the Control knob towards left.  
Return to root folder  
Push the Control knob towards left for at  
least 2 seconds.  
2 Select the muisc  
Turn the Control knob.  
“<” or “>” beside the displayed folder name  
indicates that this folder is preceded or followed by  
another folder.  
When file name is displayed, "" is added at the  
end.  
3 Play the selected song  
Press the Control knob.  
The Multi Jog Select mode is canceled and the  
selected song is played.  
Cancelling the Multi Jog Select mode  
Press the [M.JOG] button.  
Cancelling the Multi Jog Select mode  
Press the [M.JOG] button.  
Track Select is available only during playing of the built-  
in CD player.  
List Select cannot be performed during Random play or  
scan play.  
Track Select cannot be performed during Random play  
or scan play.  
|
10 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Menu Operation  
Menu System  
Set up the following functions;  
Display  
Setting Setting overview  
Source  
“RUSSIAN”*3 ON*/OFF Selects Russian as the display  
language.  
Display  
Setting Setting overview  
Source  
“SCROLL”  
AUTO/  
Scrolls the screen once when the  
“SECURITY Refer to  
Sets security code  
MANUAL* displayed text changes.  
SET”  
page 12  
“AUX”  
OFF/ON1*/ Sets whether to display AUX  
“CLOCK  
ADJUST”  
Refer to  
page 12  
Sets the clock.  
ON2  
during source selection.  
“POWER OFF” --- – 20M* Turns off the power when the  
“SYNC”  
ON*/OFF Synchronizing the RDS station  
time data and this unit’s clock.  
– 60M  
preset time has lapsed in the  
Standby mode.  
“DISPLAY” ON*/OFF Turns off the display when no  
operation is performed.  
“CD READ” 1*/2  
Sets the CD read mode.  
Specifies whether to enable  
“DEMO  
MODE”  
Refer to  
page 13 demonstration.  
“DIMMER”*1 AUTO*/OFF Dims the display in conjunction  
with the light switch of the  
vehicle.  
“DIMMER”*2 ON/OFF* Adjusts the brightness of  
the display according to the  
surrounding illumination.  
“DOT LINE” ON*/OFF Specifies whether to display the  
red dotted line on the display.  
* Factory setting  
*1 Function of KDC-W5641U/W5541U/W5141U/W5041U.  
*2 Function of KDC-W4141/W4041.  
*3 Function of KDC-W5641U/W5141U/W4141.  
Displayed item is depending on currently selected  
source. The mark in Source column shows the  
source to which the item is displayed.  
: Can be set in other than standby state.  
: Can be set in standby state.  
“SWPRE”  
REAR*/  
SUB-W  
Sets the preout output.  
: Can be set while Audio file source of CD/USB  
(excluding iPod).  
: Can be set while Tuner source.  
: Can be set during FM reception.  
: Can be set while accessing AUX source.  
“ZONE2”*1 REAR*/  
FRONT  
Specifies the destination of AUX  
input sound when the Dual Zone  
function is turned on.  
“SUPREME” ON*/OFF Turns ON/OFF the Supreme  
function.  
: Can be set during all sources.  
“NEWS”  
OFF*  
– 90M  
Turns ON/OFF the News Bulletin  
Automatic Reception function  
and sets the news bulletin  
interrupt disabled time.  
1 Enter Menu mode  
Press the [M.JOG] button for at least 1 second.  
“MENU” is displayed.  
“LOCAL S” ON/OFF* Only stations whose reception is  
2 Select the menu item  
good are searched in auto seek  
tuning.  
Push the Control knob towards up or down.  
3 Set the menu item  
“SEEK”  
“AF”  
AUTO1*/ Selects the tuning mode of  
AUTO2/  
the radio.  
Push the Control knob towards right or left.  
MANUAL  
4 Exit Menu mode  
ON*/OFF When station reception is poor,  
automatically switches to the  
station that is broadcasting the  
same program over the same RDS  
network.  
Press the [M.JOG] button.  
Refer to the respective page for information on how to  
set the items with reference page number.  
”ZONE2” is displayed when ”2ZONE” in <Audio Setup>  
(page 6) is set to ”ON.  
Refer to the <Appendix> (page 16) for the details of the  
menu items.  
“REGIONALON*/OFF Sets whether to switch to the  
station only in the specific region  
using theAFcontrol.  
“ATPS”  
ON*/OFF When traffic information station  
reception is poor, automatically  
searches for a station that can be  
received better.  
“MONO”  
ON/OFF* Receives a stereo broadcast in the  
mono mode.  
“NAME SET” Refer to  
Sets the display when switched  
page 13 to AUX source.  
English  
|
11  
Menu Operation  
and the input prohibition periods shown in the table  
below is generated.  
After the input prohibition time lapses, “CODE” is  
displayed, and you can reenter the code.  
Security Code  
When Security Code is set, possibility of theft  
is reduced because input of Security Code is  
prompted to turn on the unit once it is turned off.  
Number of times the  
Input prohibited time  
incorrect code was input  
1
2
3
4
5 minutes  
1 hour  
When you activate the Security Code function, it cannot be  
released.  
Note, your Security Code is the 4 digit number entered in  
your “Car Audio Passport” in this package.  
24 hours  
1 Select Security Code item during Menu mode  
Select the “SECURITY SET” display.  
Manual Clock Adjustment  
For how to select menu items, refer to <Menu  
System>(page 11).  
1 Select Clock Adjustment item during Menu  
mode  
Select the “CLOCK ADJUST” display.  
For how to select menu items, refer to <Menu  
System>(page 11).  
2 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When “ENTER” is displayed, “CODE” is also displayed.  
3 Select the digits to enter  
Push the Control knob towards right or left.  
2 Enter Clock Adjust mode  
Press the Control knob for at least 1 second.  
The clock display blinks.  
4 Select the Security Code numbers  
Push the Control knob towards up or down.  
5 Repeat steps 3 and 4, and complete the  
3 Adjust the time  
Security Code.  
Push the control knob towards up or down to  
adjust the hours and right or left to adjust the  
minutes.  
6 Confirm the Security Code  
Press the Control knob for at least 3 seconds.  
When “RE-ENTER” is displayed, “CODE” is also  
displayed.  
4 Exit Clock adjustment mode  
Press the [M.JOG] button.  
7 Do the step 3 through 6 step operation, and  
reenter the security code.  
“APPROVED” is displayed.  
You can do this adjustment when the “SYNC” is set as  
“OFF.  
The Security Code function activates.  
If you enter a Code different from your Security Code,  
you have to start over from step 3.  
8 Exit Security Code mode  
Press the [M.JOG] button.  
Entering Security Code  
The Security Code is required to use the audio unit  
when the unit is first used after removed from the  
battery power source or the Reset button is pressed.  
1 Turn the power ON.  
2 Do the step 3 through 6 step operation, and  
reenter the security code.  
“APPROVED” is displayed.  
If an incorrect code is entered, “WAITING” is displayed,  
|
12 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Auxiliary Input Display Setting  
Selects the display below when changing to  
Auxiliary input source;  
• “AUX”  
• “DVD”  
• “PORTABLE”  
• “GAME”  
• “VIDEO”  
• “TV”  
1 Select Auxiliary input display setting item  
during Menu mode  
Select the “NAME SET” display.  
For how to select menu items, refer to <Menu  
System>(page 11).  
2 Enter Auxiliary input display setting mode  
Press the Control knob for at least 1 second.  
The presently selected Auxiliary input display is  
displayed.  
3 Select the Auxiliary input display  
Push the Control knob towards right or left.  
4 Exit Auxiliary input display setting mode  
Press the [M.JOG] button.  
When operation stops for 10 seconds, the name at that  
time is registered, and the Auxiliary input display setting  
mode closes.  
The Auxiliary input display can be set only when the  
built-in auxiliary input or the auxiliary input of optional  
KCA-S220A is used. On the KCA-S220A, "AUX EXT" is  
displayed by default.  
Demonstration mode Setting  
Turning the demonstration mode ON/OFF.  
1 Select Demonstration item during Menu mode  
Select the “DEMO MODE” display.  
For how to select menu items, refer to <Menu  
System>(page 11).  
2 Set the Demonstration mode  
Press the Control knob for at least 2 second.  
Pressing this button for 2 seconds or longer toggles  
the setting between ”ON” and ”OFF.  
3 Exit Demonstration mode  
Press the [M.JOG] button.  
English  
|
13  
Accessory of KDC-W5641U/KDC-W5141U/KDC-W4141  
Basic Operations of remote control  
In Tuner source  
SRC  
ATT  
VOL  
AUD  
SRC  
AT T  
Band select  
[FM]/[AM]  
VOL  
AUD  
Station select  
[4]/[¢]  
FM/AM  
2-ZONE  
0 — 9  
Recall preset stations  
[1] — [6]  
DIRECT  
*
In CD/USB source  
Music select  
[4]/[¢]  
Folder/Disc select  
[FM]/[AM]  
*
Pause/Play  
[38]  
*KDC-W5641U/W5141U only  
General control  
About [  
]
This button is used when Bluetooth HANDS FREE  
BOX is connected. For more information, refer to the  
instruction manual of Bluetooth HANDS FREE BOX.  
Volume control  
Source select  
Volume reduce  
[VOL]  
[SRC]  
[ATT]  
¤
• Do not set the remote control in hot places such as  
on the dashboard.  
When the button is pressed again, the volume returns  
to the previous level. When the volume is reduced,  
the "ATT" indicator flashes.  
Loading and Replacing battery  
Use two “AA”/ “R6”-size batteries.  
Slide the cover while pressing downwards to remove  
it as illustrated.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
In Audio control  
Audio item select  
[AUD]  
[VOL]  
Adjusts the Audio item  
Refer to <Audio Control> (page 6) for the operation  
method, such as the procedures for Audio control and  
others operations.  
Dual Zone control  
Dual zone system on and off  
Rear channel volume control  
[2-ZONE]  
[5]/ []  
|
14 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Appendix  
About Audio file  
About USB device  
Playable Audio file  
• If you start playback after connecting the iPod, the  
music that has been played by the iPod is played  
first.  
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)  
Playable disc media  
CD-R/RW/ROM  
Playable disc file format  
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.  
USB device Playable Model  
KDC-W5641U, KDC-W5541U, KDC-W5141U,  
KDC-W5041U  
In this case, "RESUMING" is displayed without  
displaying a folder name, etc. Changing the browse  
item will display a correct title, etc.  
• When the iPod is connected to this unit,  
“KENWOOD” or “” is displayed on the iPod to  
indicate that you cannot operate the iPod.  
• When the USB device is connected to this unit,  
it can be charged up provided that this unit is  
powered.  
• Install the USB device in the place where it will not  
prevent you from driving your vehicle properly.  
• You cannot connect a USB device via a USB hub and  
Multi Card Reader.  
• Take backups of the audio files used with this unit.  
The files can be erased depending on the operating  
conditions of the USB device.  
We shall have no compensation for any damage  
arising out of erasure of the stored data.  
• No USB device comes with this unit. You need to  
purchase a commercially available USB device.  
Playable USB device  
USB mass storage class  
Playable USB device file system  
FAT16, FAT32  
iPod Playable Model  
KDC-W5641U, KDC-W5541U  
Although the audio files are complied with the  
standards listed above, the play maybe impossible  
depending on the types or conditions of media or  
device.  
Playing order of the Audio file  
In the example of folder/file tree shown below, the  
files are played in the order from to .  
<
v
:
Folder
Audiofile  
CD  
()  
• When connecting the USB device, usage of the CA-  
U1EX (option) is recommended.  
Normal playback is not guaranteed when a cable  
other than the USB compatible cable is used.  
Connecting a cable whose total length is longer  
than 5 m can result in abnormal playback.  
:
vꢀ  
vꢆ  
vꢇ  
vꢄ  
vꢉ  
v.  
An online manual about audio files is put on the  
site, www.kenwood.com/audiofile/. On this online  
manual, detailed information and notes which are not  
written in this manual are provided. Make sure to read  
through the online manual as well.  
In this manual, the word "USB device" is used for flash  
memories and digital audio players which have USB  
terminals.  
The word "iPod" appearing in this manual indicates the  
iPod connected with the iPod connection cable (optional  
accessory). The iPod connected with the iPod connection  
cable can be controlled from this unit. iPods that can be  
connected with the iPod connection cable are the iPod  
nano, Fifth Generation iPod, iPod classic, and iPod touch.  
Other iPods cannot be connected.  
English  
|
15  
Appendix  
SEEK (Tuning mode select)  
Select a tuning mode of the radio.  
Menu Glossary  
SWPRE (Switching Preout)  
Switches the preout between rear output (“REAR”)  
and subwoofer output (“SUB-W”).  
SUPREME  
Tuning mode  
Auto seek  
Display Operation  
“AUTO1” Automatic search for a station.  
Preset station seek “AUTO2” Search in order of the stations in the  
Preset memory.  
Manual  
Technology to extrapolate and supplement with  
proprietary algorithm, the high-frequency range  
that is cut off when encoding at low bit rate (less  
than 128Kbps, Sampling frequency is 44.1kHz).  
Supplementing is optimized by compression  
format (AAC, MP3 or WMA) and processed  
according to bit rate.  
The effect is negligible with music that is encoded  
at high bit rate, variable bit rate or has minimal high  
frequency range.  
CD READ  
Sets the method for reading CD.  
When unable to play special format CD, set this  
function to “2” to force playing. Note that some  
music CD may be unplayable even when set to “2.  
In addition, audio files cannot be played when set  
to “2. Normally, keep this set to “1.  
“MANUALNormal manual tuning control.  
AF (Alternative Frequency)  
When the reception is poor, automatically alternate  
to another frequency broadcasting the same  
program in the same RDS network with better  
reception.  
RUSSIAN (Russian language setting)  
When this is set to ON, the following character  
strings are displayed in Russian:  
Folder name/ File name/ Song title/ Artist name/  
Album name/ KCA-BT100 (optional accessory)  
1 : Automatically distinguishes between audio file  
disc and music CD when playing disc.  
2 : Forces playing as music CD.  
POWER OFF (Power OFF Timer)  
Setting the timer to turn this unit’s power OFF  
automatically when Standby mode continues.  
Using this setting can save the vehicle’s battery  
power.  
AUX  
When this is set to ON, AUX source can be selected.  
ON1: Outputs the sound of external unit connected  
to the AUX terminal when switched to AUX  
source.  
– – –: Power OFF Timer function is OFF.  
20M: Turns the power OFF after 20 minutes.  
(Factory setting)  
40M: Turns the power OFF after 40 minutes.  
60M: Turns the power OFF after 60 minutes.  
ZONE2 (Dual Zone)  
Set the destination (front speaker “FRONT” or rear  
speaker “REAR”) of the sub source (AUX IN) when  
the Dual Zone function is turned on.  
DISPLAY  
If this unit is not operated at least 5 seconds with  
“OFF” selected, the display turns off. During a setup  
mode, the display will not turn off even if 5 seconds  
lapse.  
ON2: Activates the attenuator function when  
switched to AUX source.  
Turn off the attenuator function when  
listening to output from external unit. This  
prevents the noise when no external unit is  
connected to AUX terminal.  
OFF: Disables the selection of AUX source.  
Set to OFF when not using the AUX terminal.  
NEWS (News Bulletin with Timeout Setting)  
Automatically receives news bulletin when it  
starts. Set the time during which interrupt is to be  
disabled after start of another news bulletin.  
Changing ”NEWS 00M” to ”NEWS 90M” turns this  
function ON. When this function is ON, the “NEWS”  
indicator is ON.  
If news bulletin starts when this function is ON,  
“TRAFFIC” is displayed and news is received. If ”20M”  
is has been set, reception of another news bulletin  
will not start for 20 minutes.  
The news bulletin volume is the same level that  
was set for Traffic Information.  
|
16 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
For operating KCA-BT100  
To control KCA-BT100, operate as follows;  
To make setting for <Selecting the Dialing Mode>,  
select <Menu System> (page 11). Pressing the [38]  
button for at least 1 second after selecting the  
"DIALING MODE" item allows you to enter the dialing  
method selection mode. To exit from dialing method  
selection mode, press [M.JOG] button.  
To make <Disconnecting a Call>, <Clearing the  
Disconnection Massage>, and <Rejecting an  
Incoming call>, press [AUTO] button for at least 1  
second.  
Information on Disposal of Old Electrical  
and Electronic Equipment (applicable for  
EU countries that have adopted separate  
waste collection systems)  
Products with the symbol (crossed-out  
wheeled bin) cannot be disposed as  
household waste.  
Old electrical and electronic equipment  
should be recycled at a facility capable  
of handling these items and their waste  
byproducts. Contact your local authority  
for details in locating a recycle facility  
nearest to you. Proper recycling and waste  
disposal will help conserve resources whilst  
preventing detrimental effects on our  
health and the environment.  
Moreover, some displays are different from the  
description of KCA-BT100 Instruction Manual.  
Displays of KCA-BT100 Instruction Actual displays on this unit  
Manual  
“DISCONCT”  
“CONNECT”  
“PHN-DEL”  
“P-STATUS”  
“BT-CON Y”  
“T-CON N”  
“HF DISCONCT”  
“HF CONNECT”  
“DEVICE DEL”  
“DVC STATUS”  
“HF CONNECT Y”  
“HF CONNECT N”  
The marking of products using lasers  
(Except for some areas)  
: Displays the bluetooth connection status.  
This indicator turns on when a cell-phone is  
connected to this unit.  
: Displays the signal strength of cell-phone.  
: Displays the battery level of cell-phone.  
CLASS 1  
LASER PRODUCT  
The label is attached to the chassis/case and says  
that the component uses laser beams that have been  
classified as Class 1. It means that the unit is utilizing  
laser beams that are of a weaker class. There is no  
danger of hazardous radiation outside the unit.  
Declaration of Conformity with regard to  
the EMC Directive 2004/108/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan  
EU Representative's:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands  
English  
|
17  
Accessories/ Installation Procedure  
with the ignition, connect the ignition wire to a power  
source that can be turned on and off with the ignition key.  
Use a commercially available conversion connector if the  
connector does not fit in the vehicle connector.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
If the console has a lid, make sure to install the unit so that  
the faceplate will not hit the lid when closing and opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with one  
with the same rating.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail to  
work if you share the - wires or ground them to any metal  
part in the car.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
Accessories  
1
..........1  
2
..........2  
Installation Procedure  
1. To prevent short circuits, remove the key from the  
ignition and disconnect the - terminal of the  
battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the wire on the wiring harness.  
4. Take Connector B on the wiring harness and  
connect it to the speaker connector in your vehicle.  
5. Take Connector A on the wiring harness and  
connect it to the external power connector on your  
vehicle.  
6. Connect the wiring harness connector to the unit.  
7. Install the unit in your car.  
8. Reconnect the - terminal of the battery.  
9. Press the reset button.  
About CD players/disc changers connected  
to this unit  
Kenwood disc changers/ CD players released in 1998  
or later can be connected to this unit.  
Refer to the catalog or consult your Kenwood dealer  
for connectable models of disc changers/ CD players.  
Note that any Kenwood disc changers/ CD players  
released in 1997 or earlier and disc changers made by  
other makers cannot be connected to this unit.  
Connecting unsupported disc changers/CD players to  
this unit may result in damage.  
Set the “O-N” Switch to the “N” position for the  
applicable Kenwood disc changers/ CD players.  
The functions you can use and the information that  
can be displayed may differ depending on the models  
being connected.  
¤
Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
Make sure to ground the unit to a negative 12V DC power  
supply.  
Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
Do not use your own screws. Use only the screws provided.  
If you use the wrong screws, you could damage the unit.  
If the power is not turned ON (“PROTECT” is displayed),  
the speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not  
be linked with the ignition (i.e., it will not turn on and off  
along with the ignition). If you want to link the unit’s power  
|
18 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Connecting Wires to Terminals  
KDC-W5641U/W5541U/W5141U/W5041U  
Steering remote control (Light Blue/Yellow)  
REMO.CONT  
L
R
R
Rear preout/SubWoofer preout  
To use the steering wheel remote control feature, you need to an exclusive  
remote adapter (not supplied) matches your car is required.  
When this terminal is not in use, leave its cap on.  
KDC-W4141/W4041  
L
Rear/SubWoofer preout  
R
FM/AM antenna input (JASO)  
(KDC-W5641U/W5541U/W5141U/W5041U)  
FM/AM antenna input (JASO)  
(KDC-W4141/W4041)  
To Kenwood disc changer/  
External optional accessory  
Fuse (10A)  
Wiring harness  
(Accessory1)  
TEL mute wire (Brown)  
Connect to the terminal that is grounded when  
either the telephone rings or during conversation.  
MUTE  
To connect the Kenwood navigation system,  
consult your navigation manual.  
If no connections are made, do  
not let the wire come out from  
the tab.  
Power control/ Motor  
antenna control wire  
(Blue/White)  
Connect either to the power control terminal  
when using the optional power amplifier, or to the  
antenna control terminal in the vehicle.  
P.CONT  
ANT.CONT  
Battery wire (Yellow)  
Ignition wire (Red)  
See next page.  
A–7 Pin (Red)  
A–4 Pin (Yellow)  
Connector A  
Connector B  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
English  
|
19  
Connecting Wires to Terminals  
Connector Function Guide  
Pin Numbers for Cable Colour  
ISO Connectors  
External Power  
Connector  
2WARNING  
Functions  
Connecting the ISO Connector  
The pin arrangement for the ISO connectors depends on  
the type of vehicle you drive. Make sure to make the proper  
connections to prevent damage to the unit.  
A-4  
A-5  
A-6  
A-7  
A-8  
Yellow  
Battery  
Power Control  
Dimmer*  
Ignition (ACC)  
Earth (Ground)  
Connection  
The default connection for the wiring harness is described in  
1 below. If the ISO connector pins are set as described in 2  
or 3, make the connection as illustrated.  
Please be sure to reconnect the cable as shown 2 below to  
install this unit to the Volkswagen vehicles etc.  
Blue/White  
Orange/White  
Red  
Black  
Speaker  
Connector  
B-1  
B-2  
B-3  
B-4  
B-5  
B-6  
B-7  
1(Default setting) The A-7 pin (red) of the vehicle’s  
ISO connector is linked with the ignition, and the A-  
4 pin (yellow) is connected to the constant power  
supply.  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right (–)  
Front Right (+)  
Front Right (–)  
Front Left (+)  
Front Left (–)  
Rear Left (+)  
Rear Left (–)  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
B-8  
Green/Black  
2The A-7 pin (red) of the vehicle’s ISO connector is  
connected to the constant power supply, and the  
A-4 pin (yellow) is linked to the ignition.  
Ignition cable  
*Function of KDC-W5641U/W5541U/W5141U/W5041U.  
A-7 Pin (Red)  
(Red)  
Unit  
Vehicle  
A-4 Pin (Yellow)  
Battery cable  
(Yellow)  
3The A-4 pin (yellow) of the vehicle’s ISO connector  
is not connected to anything, while the A-7 pin  
(red) is connected to the constant power supply  
(or both the A-7 (red) and A-4 (yellow) pins are  
connected to the constant power supply).  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
When the connection is made as in 3 above, the unit’s  
power will not be linked to the ignition key. For that reason,  
always make sure to turn off the unit’s power when the  
ignition is turned off.  
To link the unit’s power to the ignition, connect the ignition  
cable (ACC...red) to a power source that can be turned on  
and off with the ignition key.  
|
20 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
Installation/Removing the Unit  
Installation  
Removing the hard rubber frame  
Metal mounting strap  
1 Engage the catch pins on the removal tool and  
remove the two locks on the upper level.  
Upper the frame and pull it forward as shown in  
the figure.  
(commercially available)  
Firewall or metal support  
Lock  
Catch  
Bend the tabs of the  
Accessory2  
mounting sleeve with a  
screwdriver or similar utensil  
and attach it in place.  
Removal tool  
2 When the upper level is removed, remove the  
lower two locations.  
Self-tapping screw  
(commercially available)  
The frame can be removed from the bottom side in the  
same manner.  
Screw (M4X8)  
(commercially available)  
Removing the Unit  
Make sure that the unit is installed securely in place. If the  
unit is unstable, it may malfunction (for example, the sound  
may skip).  
1 Refer to the section <Removing the hard rubber  
frame> and then remove the hard rubber frame.  
2 Remove the screw (M4 × 8) on the back panel.  
3 Insert the two removal tools deeply into the slots  
on each side, as shown.  
4 Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
Screw (M4X8)  
(commercially available)  
Accessory2  
¤
Be careful to avoid injury from the catch pins on the  
removal tool.  
5 Pull the unit all the way out with your hands, being  
careful not to drop it.  
English  
|
21  
Troubleshooting Guide  
Some functions of this unit may be disabled by  
some settings made on this unit.  
Audio file source  
? The sound skips when an Audio file is being  
played.  
!
• Cannot set up the subwoofer.  
• Cannot set up the High Pass Filter.  
• Cannot set up the Fader.  
The media is scratched or dirty.  
Clean the media, referring to the CD cleaning of  
the section on <Handling CDs> (page 3).  
• No Audio control effect on AUX.  
• Preout is not set to subwoofer. “SWPRE” of  
<Menu System> (page 11)  
The recording condition is bad.  
Record the media again or use another media.  
• “Subwoofer output” of <Basic Operation> (page 4)  
is not set to On.  
• The Dual zone function is enabled. <Audio  
Setup> (page 6)  
!
!
Cannot set up the subwoofer phase.  
The Low Pass Filter is set to Through. <Audio  
Setup> (page 6)  
• Cannot select the output destination of the  
subsource in the Dual zone.  
• Cannot adjust the volume of the rear speakers.  
The Dual zone function is disabled. <Audio  
Setup> (page 6)  
!
!
• Cannot register a security code.  
• Cannot set up Display Illumination Control.  
<Demonstration mode Setting> (page 13) is not  
turned off.  
Cannot set up the Power-off timer.  
<Security Code> (page 12) is not set.  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
Tuner source  
? Radio reception is poor.  
The car antenna is not extended.  
Pull the antenna out all the way.  
Disc source  
? The specified disc does not play, but another one  
plays instead.  
The specified CD is quite dirty.  
Clean the CD.  
The disc is loaded in a different slot from that  
specified.  
Eject the disc magazine and check the number  
for the specified disc.  
The disc is severely scratched.  
Try another disc instead.  
|
22 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  
USB ERROR/USB (Blink):  
Some trouble may have occurred to the  
The messages shown below display your  
systems condition.  
connected USB device.  
Remove the USB device, then cycle the  
power switch to ON. If the same display is  
repeated, use another USB device.  
TOC ERROR:  
• No disc has been loaded in the disc  
magazine.  
• The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
iPod ERROR:  
Connection to the iPod has failed.  
Check that the connected iPod is an iPod  
that is supported. See <About Audio file>  
(page 15) for information on supported  
iPods.  
Remove the USB device and then  
reconnect it.  
E-05:  
E-77:  
The disc is unreadable.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the “E-  
77” code does not disappear, consult your  
nearest service center.  
Confirm that the software for the iPod is  
the latest version.  
E-99:  
Something is wrong with the disc magazine.  
Or the unit is malfunctioning for some reason.  
Check the disc magazine. And then press  
the reset button on the unit. If the “E-99”  
code does not disappear, consult your  
nearest service center.  
USB REMOVE: The Remove mode has been selected for the  
USB device/iPod. You can remove the USB  
device/iPod safely.  
IN (Blink):  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
PROTECT:  
The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and then  
the protection function is activated.  
Wire or insulate the speaker cable  
properly and press the reset button. If  
the “PROTECT” code does not disappear,  
consult your nearest service center.  
NA FILE:  
An Audio file is played with a format that this  
unit can’t support.  
COPY PRO:  
A copy-protected file is played.  
READ ERROR: The file system of the connected USB device  
is broken.  
Copy the files and folders for the USB  
device again. If the error message is still  
displayed, initialize the USB device or use  
other USB devices.  
NO DEVICE:  
N/A DEVICE:  
The USB device is selected as a source  
although no USB device is connected.  
Change the source to any source other  
than USB. Connect an USB device, and  
change the source to USB again.  
An unsupported USB device is connected.  
Remove the USB device without entering  
the remove mode.  
NO MUSIC DATA/E-15:  
• The connected USB device contains no  
playable audio file.  
• Media was played that doesn’t have data  
recorded that the unit can play.  
English  
|
23  
Specifications  
FM tuner section  
Frequency range (50 kHz space)  
: 87.5 MHz – 108.0 MHz  
Usable sensitivity (S/N = 26dB)  
: 0.7 μV/75 Ω  
Quieting Sensitivity (S/N = 46dB)  
: 1.6 μV/75 Ω  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 65 dB  
Selectivity (DIN) ( 400 kHz)  
: ≥ 80 dB  
Stereo separation (1 kHz)  
: 35 dB  
USB Interface  
(KDC-W5641U/W5541U/W5141U/W5041U)  
USB Standard  
: USB1.1/ 2.0  
Maximum Supply current  
: 500 mA  
File System  
: FAT16/ 32  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC ".m4a" files  
Audio section  
Maximum output power  
: 50 W x 4  
Full Bandwidth Power (at less than 1% THD)  
: 30 W x 4  
MW tuner section  
Frequency range (9 kHz space)  
: 531 kHz – 1611 kHz  
Usable sensitivity (S/N = 20dB)  
: 25 μV  
Speaker Impedance  
: 4 – 8 Ω  
Tone action  
LW tuner section  
Frequency range  
: 153 kHz – 281 kHz  
Usable sensitivity (S/N = 20dB)  
: 45 μV  
Bass : 100 Hz 8 dB  
Middle : 1 kHz 8 dB  
Treble : 10 kHz 8 dB  
Preout level / Load (CD)  
: 2500 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
CD player section  
Laser diode  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 24 Bit  
Spindle speed  
: 500 – 200 rpm (CLV)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
: 0.008 %  
Auxiliary input  
Frequency response ( 1 dB)  
: 20 Hz – 20 kHz  
Input Maximum Voltage  
: 1200 mV  
Input Impedance  
: 10 kΩ  
General  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 53 x 155 mm  
Weight  
: 1.40 kg  
Signal to Noise ratio (1 kHz)  
: 105 dB  
Dynamic range  
: 93 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC ".m4a" files  
Specifications subject to change without notice.  
|
24 KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041  

Pioneer Car Stereo System DEH P5100UB User Manual
Panasonic CQ 5302U User Manual
Panasonic Cordless Phone With Answering Machine KX TG7642M User Manual
Orion STARSHOOT 52187 User Manual
Listen Technologies LBB 4500 User Manual
Laney Amplification Car Amplifier KD65 User Manual
Kodak Digital Frame 1 User Manual
Kenwood IN DASH DNX7180 User Manual
JVC LYT1643 001A User Manual
JVC KV C1000 User Manual